Search results

Hot as in real hot. Too hot to touch except briefly and it only takes seconds. ---------- Post added at 12:03 PM ---------- Previous post was at 11:33 AM ---------- I have the back end off the ground and it still heats up pretty fast. Not having prior experience with mini's and 3-wheelers, I...

Okay Sid, Yesterday I removed the TAV2 and gave it a good cleaning. Re-installing a piece at a time, I checked the bearings (5/8") on the driven shaft and they seem okay. Shafts are parallel and perpendicular to the mounting face. I added and subtracted shims on the driver and could not find a...

Sid, At present I have aTAV2 frthe chain runs to a 28om BMI with 10T#41 chain. From the 10T it runs to a 28T on the jackshaft. The jackshaft out is 10T going to a 60T final drive. That equates to 16.8:1 final drive. Pictures of the machine are in the Timber Wolf thread. ---------- Post added...

TC questions for Sid Sid, I have to admit that I am new at this game and would be happy for all the advice you are willing to give. My 3-wheeler build is based on what I have read about others doing. The TAV2 from BMI is not a precision part, just trying to get the thing to work the best I...

Okay Sid, I have installed the yellow spring and a new belt on the 3-wheeler. It made a difference. Why should I not use the yellow spring? What should I use to get the claimed changes from the yellow spring? Want to stay in lower rpm range longer. I think I found the reason I tossed and broke a...

Whitetrashrocker, thank you for the observation. I had intended to redo my JS and put in a third bearing support. Guess it will be sooner rather than later. When I do I am going to change sprockets and use a smaller final sprocket and a larger JS in sprocket. Want to raise ground clearance...

Pictures of the 3-wheeler are on the Atomic Zombie thread.

Ordered a Comet belt from BMI and a yellow spring for the driven. I am also going to raise the jackshaft to allow me to run the disc brake rotor and a larger JSin sprocket. Then I will use a smaller sprocket on the axle to give more ground clearance while keeping a low ratio.

Everything is in alignment, have an idler for take up, lube chain every other day because of the dirt and silt. I was in the middle of a left hard turn, putting more weight on the drive wheel, and cranked the throttle on and it snapped at the master link. The whole chain and sprockets have less...

Just snapped the main link and at least one link of the chain. Chain is Chinese from Tractor Supply. What is a strong #41 chain for my 3-wheeler? Didn't think the Predator Hemi had this much torque.

I straight edged the backing plates and had to add one thin washer to the driver to align. Used to be a machinist and still have my tools, would not want to have to buy them today. Everything seems to be working fine now.

I tried with the recumbent seat first and decided that it would be nice on a street trike, but less nice in the dirt where 90% of my riding will be.

The odor of burning belt is gone, do all new belts wear in?

Pictures are on the Atomic Zombie thread. I have changed my thoughts that I am not geared low enough, dug a hole with the drive wheel and had to toss s piece of concrete in the hole to move forward. The Dirt Devil tires really dig. I have the red spring ine the torque hole and it seems to go...

I rode to our local village, around 10 miles max. The coil spring has the right rate and I can go top speed over most bumps, rides like a Caddie. Was thinking my final gear ratio was not low enough (16.68:1), but now I think it is okay. Have made changes already on some minor issues. Working...

more pictures

We have been having fits this weekend trying to figure out how to send pictures. Don't know if we have it or not.

I took my trike for its break in run yesterday. Could smell the belt on the BMI TAV slipping and eventually grab. The present gearing: TAV sprocket-10T JS driver-28T JS driven-10T Axle sprocket-60T Tire dia.-22"X11"-8 I believe that this gives a 16+:1 rear gear ratio. Is this...

I finished the trike enough to test ride it yesterday. Will be taking pictures today and the wife says she knows how to post them, couple of days. Made 4+ mods already after the ride. Cut the header I bought for the 212 hemi and added larger OD DOM tube and it sound real throaty. Not crazy about...

Whether you believe me or not is of no concern to me. I just received the material to make my forks and cables and grips. I hope to have the trike operational by thie weekend and then I will have the wife help me to take and post pictures next week. Sorry if the temporary lack of pictures rubs...