Search results

Well it's not really an off road kart. I put it together with scraps that I had laying around. I will never do that again because you just add more time and energy which isn't fun. It's worth waiting for the right material.

Thanks for the response red. I weigh around 180lbs. I always had issues with the drive system such as the chain coming off or the engine would seem to be running a bit hot, though I couldn't confirm it. The thing is if I add a 72 tooth sprocket on the axle the kart will be really slow.

I built this kart in like 2017 or 2018 and I never got around to fully finishing it. I want it to be fully finished without any issues. I finally painted it. Now I am wondering if my go kart wheels are to big for a 212cc engine. I have a chinese torque converter from amazon. The axle sprocket is...

If it's a chinese quad it maybe a 250cc I think the 125cc sized quads are less than 1k $700-$900 US dollars. I would buy it in a heart beat. I have a 110cc that I fixed up and that thing is a lot of fun and has a decent amount of sack for it's engine size.

Guys I need help please. I'm about to redo my steering never got a chance til now. I get what caster does it helps stabilize steering straight and other effects. Camber also helps with that from looking above camber is the tilt of the tire or possibly king pin. What I really want is a simple...

Yes it is nice and flat however I did not square the mounting plate to the axle like make it paralell to the axle I just measured and cut then welded. ---------- Post added at 11:39 PM ---------- Previous post was at 11:14 PM ---------- I forgot to add that I finally was able to take the kart...

So I bought another crankshaft oil seal. Yesterday I ran the engine on a wooden engine jig for 5 minutes no oil leaking and I revved it pretty high as well. Today I install the engine on the go kart and let it run and it starts leaking oil through the crankshaft seal roughly after 2 minutes of...

J.S. Thanks for the response. I have had the engine running good but some how yesterday it wouldn't fire up after I put the crankcase back on. It had compression at first but then the compression went and oil was coming out the crankshaft case seal. I believe I didn't fully seat the new seal. I...

Thanks I have my mind setup on what I am going to do plus that link was very helpful. I'm going to bookmark it for reference when I need it. I got the engine back on the go kart today as I was trying to get it started I lost compression and oil is leaking from the crankshaft bearing. I just...

Whats up guys my go kart is almost done it just needs a few things done mechanically and then some paint. The thread I started is closed for some reason probably because it was old. This go kart frame started out as a metal motorcycle shipping frame that I bought at the scrap yard. If you...

One thing I don't understand is motorcycle frames don't look more rigid then go karts and they seem to handle the HP I wonder if it's all in the geometry of the frame.

Well in my haste I made the front tires width 44 inches wide from center to center of front tires. The kart seems wider than most go karts and I'm not sure if I should bring the spindles in more or not because I will have a hard time finding an axle long enough to match the width of the front.

The kart has evolved into a two seater. I have a few questions though is it alright to build the steering system like the steering wheel neck, pitman arm, tie rods and also weld the spindle axles to the frame without the tires? The only thing I can think of is the bore of the tire needs to match...

Hi I have been registered for awhile now I was going to build a two seat go kart like two years ago instead I built a lathe but now it's time to build the go kart. Most of the go kart will be made instead of purchasing kits. I have never built a go kart so this will be a learning experience for...

well thanks for the feedback I appreciate other people's ideas. I have already made a sketch I'll try to make up my mind.

well I don't see how the engine won't fit since it sits in the back and regardless of engine design I would leave enough clearance in the back. The tires I won't install until I'm sure of the diameter of the axles/hubs and the wheels. The reason why I don't like to do plans up front is because...

Well I understand what you are saying I've been there however I was planning on only going so far until I get the rest of the parts for example: I was going to start welding the main rectangle part of the frame, the seat and head bar and side guards as well. After that I was thinking of waiting...

Sweet so I'm on the right track. I was thinking of not making the frame design plans and build the frame as I go, this way I can design the frame as I go and if I want to add something later to the design I can. All I have right now is the frame material and steering wheel I'm wondering if I...

Hey guys what do you think of gas piping for the frame. The total outside diameter is 1'1/4 wide and the wall thickness is around a 16th give or take. At first I thought that it would be to heavy and the lighter the better but some guy I met at the local scrap yard told me that it was fine and...

well the side plate he said was a piece that attached the power washer to the engine and now there are for holes into the block/crankcase that need to be plugged somehow not sure if they are threaded or not though. Going to check it out as soon as I can thanks