Performance gains from adding reeds to a piston port two stroke?

Status
Not open for further replies.

Kaptain Krunch

Pro Junk Collector
Messages
4,636
Reaction score
6
Location
vermont
I have a 440 twin two stroke, its pretty basic, single carb, piston port, fan cooled. Anyways, what kind of gains would i see from adding reeds? Stock this thing puts out no more than 50hp, I'm planning on switching it over to duel carb anyways, and if its worth the extra machining time i could easily add a set of reeds from a polaris engine i have sitting around.
 

mike75925

thinker and tinkerer
Messages
1,753
Reaction score
4
Location
Alto, tx
thin reeds help in low and mid, thicker help on top. multi-reeds are like adding another intake valve.
 

Kaptain Krunch

Pro Junk Collector
Messages
4,636
Reaction score
6
Location
vermont
Basically what im wondering is will the power gains be worth the extra machining time, I could easily see myself spending an extra two hours or more making them "reed friendly", it would take me a half hour or less to make a couple straight intakes.
 

mike75925

thinker and tinkerer
Messages
1,753
Reaction score
4
Location
Alto, tx
as far as i know, there are two types of twostrokes. ones where the piston comes down far enough to see the piston's crown, the other all you see is piston skirt, maybe two holes in the skirt. from what i have read, all two strokes can excel with reeds. personally, i don't really see how reeds help if the piston does not come all the way down
 

Kaptain Krunch

Pro Junk Collector
Messages
4,636
Reaction score
6
Location
vermont
personally, i don't really see how reeds help if the piston does not come all the way down

try to picture the flow of fuel in your head.

I'm leaning towards just going dual carb and forgetting about reeds, it would be quite a bit of work, and i cant see the gains being that great.
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
I have two identical 2 cycle engines with one exception
One of them is reed inducted the other is piston ported.
The piston ported model is rated at 7HP whilst the reed inducted engine is 6.5HP.
The 6.5HP reed engine blows away the 7HP. Go figure.
One other small difference is that the piston ported power plant uses a lighter oil mix.
 

jr dragster T

New member
Messages
3,966
Reaction score
10
Location
Cold place
My friend has a Polaris Indy 340 piston port sled and it requires 35 pilot jets to get it to idle. My reed valve 440 requires only 17.5 pilots. I'm told piston port motors dont draw fuel in at idle very well.
 

Kaptain Krunch

Pro Junk Collector
Messages
4,636
Reaction score
6
Location
vermont
I'll have to check what size pilot jets are in my carb.

Would the reed cages i have be too big? im not sure how size affects reeds, besides the weight of the petals or whatever you want to call them. The ones i have are from a 750 triple, which was L/C and much higher strung than this 440.
 

pmat

noob
Messages
191
Reaction score
0
Location
lake wynonah, pa
my boat engine wont run without reeds (dont ask how i know), so im sure they would be a great add on to a engine that actually runs without them.
 

mike75925

thinker and tinkerer
Messages
1,753
Reaction score
4
Location
Alto, tx
kap'n, on the one type, the piston to sleeve might be two mils different. the fuel oil would increase the working pressure of the vacuum. seems pointless to me to run them when it is that tight. how much pressure do you think you would loose in that scenario? my thoughts are it would be very negligible loss if any.
 

mike75925

thinker and tinkerer
Messages
1,753
Reaction score
4
Location
Alto, tx
the reeds will help tune the powerband, as well as a chamber, port size/shape, carb, jets etc
 
Status
Not open for further replies.
Top