Advanced Hemi 212cc Predator Build

Status
Not open for further replies.

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,874
Location
Chicago-town USA
I'm only a man.... I can only make 1 kitty purrrr at a time. Lol.

If I'm ok to start her up with no load, I will.
But, Hold me! I'm scared!!!
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
I'm only a man.... I can only make 1 kitty purrrr at a time. Lol.

If I'm ok to start her up with no load, I will.
But, Hold me! I'm scared!!!

Its a good thing this is a family friendly Forum! :surrender:

She can go home and Pet her cat, Start that Engine. LOL
 

Jrgunn5150

Rudderless
Messages
1,028
Reaction score
12
No kidding, she's hot and all, but we want to see this thing run, or blow, or whatever lol.
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,874
Location
Chicago-town USA
U will get the video tomorrow. Start or not. I'lll post it if I don't end up lighting the whole thing on fire.

---------- Post added at 01:55 AM ---------- Previous post was at 01:53 AM ----------

No kidding, she's hot and all, but we want to see this thing run, or blow, or whatever lol.

That makes 4 of us! I'll start her up tomorrow!
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,874
Location
Chicago-town USA
Let's see it! I'll hold ur beer :) lol

i may have missed the answer but, What gear ratio you runnin' ? Speed test?

I got me some 60:8 for 7.5:1 with 16" tires. I have 18.5" tires I will try once I know it runs.
It seemed to top out near 36-37mph with 7.5:1 and 16"tires and went from 0-30mph in 9-10 seconds. max RPM was near 5100 before the rebuild with 7.5:1 and 16"ers

Oh... with TC, to clarify.

With 6:1, it topped out near 40 mph.

I for sure will take measurements with new parts.

Give me a minute to sober up and I'll try to start it.

---------- Post added at 08:20 AM ---------- Previous post was at 08:04 AM ----------

No vids? Boooo

Let me find the fake go pro. Hopefully it's easier to find than the oil drain plug, which I thought I lost too. lol

---------- Post added at 08:40 AM ---------- Previous post was at 08:20 AM ----------

https://www.youtube.com/watch?v=PvF9PAxe5Ng&nohtml5=False
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,874
Location
Chicago-town USA
Metallica didn't help.
I can post a video, but it will be a sad one.
It's OK for men to cry, right?

It's does 't want to try to start.

I wish it was spark or fuel, but both seem ok.
I tested compression but would rather not believe the Harbor Freight tool that barely moved.
Perhaps my tears messed up the reading.

Let me think about what I've done and ask SIRI where tall bridges are located.

---------- Post added at 10:19 AM ---------- Previous post was at 10:18 AM ----------

I think I'll return the compression tool out of anger and sadness and try a new one

---------- Post added at 10:22 AM ---------- Previous post was at 10:19 AM ----------

https://m.youtube.com/watch?v=QHdGySZLcIQ
 

FreeRunner15

=======
Messages
660
Reaction score
10
Location
================
I'm scared to even say this..

but you didn't go too crazy with the porting ,did you?


But who knows :).. maybe someone removed the guts of the compression tester and returned it :D lol.

"i dunno sir, it just doesnt work"

Reminds me of what someone said on here :rolleyes:
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,874
Location
Chicago-town USA
Should of waited to try to start it. The thought of taking it apart again and starting over, combined with this hangover, leaves me uninspired to even take out a single screw.

I'm so invested at this point, 99 bucks for a new engine - worst case - wouldn't be much of a speed bump. I'm sure it would go quicker too and come out better, but the thought is demoralizing.

---------- Post added at 10:48 AM ---------- Previous post was at 10:40 AM ----------

I don't think I did too much porting. But, this being my thirst time trying most of this, have nothing to compare to -except pictures.

Could very well be the head gasket mating surface, or piston rings????
I'll check valves first, but feeling very uninspired at the moment.

---------- Post added at 11:17 AM ---------- Previous post was at 10:48 AM ----------

Honestly I'm more thinking it's the spark plug threads?
I used Torque Wrench this time to 15 ft lb. It went in easy. Last time I don't remember if I had a Torque Wrench? Also the spark plug gasket is shot.

I'll get a new gasket for the plug, but I'll have to see what I can do if it's the threads.
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,874
Location
Chicago-town USA
Maybe I'll get some riding in today?
If my Step Father only knew the dirty thoughts I had
 

Attachments

  • image.jpg
    image.jpg
    470 KB · Views: 5

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,874
Location
Chicago-town USA
I'll bro ably break it if I touch it. Lol

---------- Post added at 12:50 PM ---------- Previous post was at 12:41 PM ----------

I tried choke on, choke off. I tried both with a little throttle. I tried the original spark plug (had better washer). Fuel screw is two turns out. I'll play with the idle screw in a bit after I clean my tears and garage.

---------- Post added at 01:04 PM ---------- Previous post was at 12:50 PM ----------

Imagine if that is how this thread ends. 10 pages of fart jokes, then a picture of a lawn tractor. Lmao

**** this battle with the Predator!
I've only manage to take one of the first three rounds.
 

Jrgunn5150

Rudderless
Messages
1,028
Reaction score
12
I agree, you probably have the lash wrong on it, if you have determined you are getting spark and fuel.
 
Status
Not open for further replies.
Top