What does this include?

[killthewhelp]

I am looking for spindle assemblies. I found this one that says "spindle only." There are also ones that say "Spindle and Bracket set."

My question is this: what is included in the "spindle only" item? Is it everything but the bracket? Our frame has brackets welded on, so I don't think we will need brackets.
May seem like a simple question, but I'm not very familiar with the part names and just want to be sure I am getting what I need.
Thanks!

 

[jr dragster T]

The "Spindle only" Just come's with the spindle. Which is the peice that swivel's with the 3/4" axle on it. Bracket is what look's like a "C" bracket.

 

[r_chez_08]

wow their expensive!! just make them, plans here http://www.diygokarts.com/kart-plans/steering-plan-spindles.html

 

[jr dragster T]

12.99 each? Not that bad, It will cost you more in steel to make them.

 

[r_chez_08]

what, a bit of tubing, bit of sheet, and 1 bolt costs $12.99! god america must have expensive steel, but i think everythings expensive as i am on a low budget....

 

[killthewhelp]

Well, time is no matter, as half the fun of this kart is building it.
I am also on a very low budget. My goal is really just to keep it as low-cost as possible. I think I can manage to build that myself, and I am always more inclined to do it myself instead of buying, if possible. I am in the marker for a welder anyway, so I should pick one up soon. Probably just a little 110 arc welder will do what I need.

 

[jarcynvicnchris93]

Welders

Well, time is no matter, as half the fun of this kart is building it.
I am also on a very low budget. My goal is really just to keep it as low-cost as possible. I think I can manage to build that myself, and I am always more inclined to do it myself instead of buying, if possible. I am in the marker for a welder anyway, so I should pick one up soon. Probably just a little 110 arc welder will do what I need.

If you are unfamiliar with Welders be sure to read the "Using Tools and Welding" section on this forum. there are some great threads about buying welders, different types of welders, and other types of tools. Many new people unfamiliar with welding have found that section very useful. as far as 110 Wleders go Miller and Lincoln both make a very nice 110 Mig that I have used. The Lincoln that I tried was the Weld Pak 100. I was very impreesed with the quality of welds it was capable of. The Miller I tested was the Millermatic 140 and it was equally impressive. My personal Welder is about the same size as the Lincoln Weld Pak 100 except mine is a 220. Hobart makes a 110 welder that tends to run cheaper than the Miller or the Lincoln and it still can produce nice welds. Also you must decide if you will be using Gas or going Flux Core. Good luck shopping.

 

[killthewhelp]

Awesome, I will check out that section. Thanks a lot for the information.

 

[Kenny_McCormic]

Well, time is no matter, as half the fun of this kart is building it.
I am also on a very low budget. My goal is really just to keep it as low-cost as possible. I think I can manage to build that myself, and I am always more inclined to do it myself instead of buying, if possible. I am in the marker for a welder anyway, so I should pick one up soon. Probably just a little 110 arc welder will do what I need.

110 volt arc welders arent worth it, go with a 230 amp 220 volt unit(can be had used for the same as a new 110 unit)or leave stick welding alone.

If you only have 110 access go with a cheap fluxcore wire welder, with good wire and an hours practice you can be making good strong welds.

 

[killthewhelp]

Well, I am looking to spend less than $150 if I can. I won't be welding anything heavier duty than the go kart frame. Do you think something like this would be sufficient? I can't find the duty cycle though...

 

[Kenny_McCormic]

Duty cycle probably sucks, the nice ones are 100% in the lower amp ranges.

http://www.homedepot.com/webapp/wcs...3&productId=100041326&N=10000003+90401+502421

Look on ebay(local only, a good one is too heavy to ship practically) and craigslist for something similar(200+amp) to the above used. DC is nice but not required. You can easily get one for under $150 with a mask and some rods.

I like 7014 rod, be careful to keep your rods dry, keep them in a dry part of the house/heated garage.

 

[jarcynvicnchris93]

trust me

I agree with Kenny to a point, but for a $150 your not gonna get a decent 110 mig. you would have to lay out some cash and get a Millermatic and it is way more than a $150. I have used the Millermatic and the Lincoln 110 w/gas and they were awesome. and I have been welding for a while. I would buy one but I already have a nice 220 unit. Check out Craigslist for a cheap flux core. I personally cant stand flux core. I would rather OA or Stick weld than use flux core. JMHO
But for the money you cant beat them. I have heard guys on here say that if you lay out the money for decent quality wire that even a cheap flux core welder will do a decent job. and even good wire is cheap considering. So maybe it would be worth trying. Also your local library is a good source for books for beginning welders. But nothing is as good as getting out there and trying it. You can also find some videos on the net that show proper technique. Good luck and keep us posted on your progress.

 

[Kenny_McCormic]

I didnt say anything about MIG, stick is 10x dirtier than fluxcore with good wire(brush VS hammer+chisel). IMO fluxcore is the only way to go for a noob on a budget, only one setting to control, point and shoot.

 

[JROY82]

I have the $100 harbor freight flux core welder and while my beads are still ugly, they hold good. The name brand wire is definately a must, which I found at Tractor Supply for $20. It doesnt do too well with thin metal but all in all I am very satisfied with it. Oh and a good auto darkening helmet is a must as well.

 

[jarcynvicnchris93]

oops

I didnt say anything about MIG, stick is 10x dirtier than fluxcore with good wire(brush VS hammer+chisel). IMO fluxcore is the only way to go for a noob on a budget, only one setting to control, point and shoot.

sorry Kenny I kind of have MIG on the brain for some reason today. yeah I have to agree "IMO fluxcore is the only way to go for a noob on a budget, only one setting to control, point and shoot" yep!! the only thing he should probably do is get good quality wire for that flux core. the cheap wire can quickly frustrate a Noob. however stick is not a bad way to go either (but yeah it is dirty). I learned how to weld with OA and then spent quite a while sticking it. also I think almost as important as the welder and in some ways more important is the mask or hood. I think if anything spend some money and get a good auto darkening hood. sometimes you can find good used ones on Ebay. I got my Hobart Auto Darkening Hood at a Garage sale of all places. and by golly wear some long gloves so you dont get sun burned..