yerf dog cart

Status
Not open for further replies.

jride1999

New member
Messages
13
Reaction score
0
i bought a yearf dog cart with a 6.0 Tecumseh motor.looking to upgrade to a bigger motor.question im asking is whats best motor to upgrade to? looking for 8-11 hsp motors.anyone run ones from harbor freight?is it gona b alot of work switching over to diff motor,realy like one with elec start.any help is good thanx
 

speedshopmike

New member
Messages
93
Reaction score
0
Location
the nation's crapital
almost all motors rated over 6.5HP use a larger 1" output shaft.
yours now is 3/4".
this means buying either a 1" driver for your existing cvt (which is only rated to 8HP) or buying a complete, beefier cvt like a comet 40, for example.
briggs makes a 3/4 shaft motor with something like 10HP; that's your best bet if you don't wanna change the drivetrain.
the actual engine swap is very straightforward/simple.
 

jride1999

New member
Messages
13
Reaction score
0
ok thanx,for the help.not looking for alot of speed,just more power,my kids use the cart in the woods,an seems with motor on it now wont go up small hills or threw mudd.so wanted to go to bigger motor.
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
You could just lower your gearing to give you more torque. You will sacrifice some speed, but you might then not have change out your engine.

What are the tooth counts on your clutch and rear sprocket?
 

jride1999

New member
Messages
13
Reaction score
0
its belt drivn but has a chain also.id like to keep the motor but need lil more power,for offroading an etc.
 

*ryan

New member
Messages
25
Reaction score
0
that has a gear reduction on it
which i dont think you want
it will make you go slower unless you change around your gearing
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
yes that will work.

i suggest getting a 9 tooth on the jackshaft, too, even if you get the bigger engine. sometimes they have 10 teeth.

the smaller you can go on the top sprocket, and the bigger you go on the axle sprocket, the more power you will have.

however, the more torque/power you change the gearing to, the slower its top speed is. i assume this isnt a big deal for going in the woods if you can barely get to top speed.
 

jride1999

New member
Messages
13
Reaction score
0
ok thanx,my kids use the cart in woods an yard,an parking lot. now it says Same physical size as former 6.5hp,does that mean the measurment's?Is certain brigs motors u can ad afetrmarket parts to or any?my engine has a belt an sproket,question is wont i get more power or speed without belt drivn an run a chain clutch?
 

jride1999

New member
Messages
13
Reaction score
0
well found a brigs 6.5 inteck motor cheap,only been started 3 times.prob is the shaft is shorter then the techumsi shaft. the torque convertoer wont fit on shaft cause shaft is to small.can i just run a clutch? the shaft is only about 1-2"
 

jride1999

New member
Messages
13
Reaction score
0
the brigs mounted right up on the mounting plate,now gota figure out a clucth or so,an does anyone have pics of there throttle set up?
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
what do u mean beef it up?everything mounted up sept shaft is lil shorter.

The rear deck of these karts are very weak and even with the stock engine they have a habit of twisting and breaking at several joints.

It is essential to beefing these decks up with supports to keep it from destroying itself under the torque.
 

speedshopmike

New member
Messages
93
Reaction score
0
Location
the nation's crapital
jride, keep the cvt on the cart.
it'll be a slug without it.
just use a longer bolt to install the drive pulley; it'll accommodate a shorter crank output shaft.
however, unless there's something wrong with your old tecumseh motor don't expect to go any faster w/ the briggs.
 
Status
Not open for further replies.
Top