Won't Stay Running (Electrical)

Status
Not open for further replies.

hotrodhenson

New member
Messages
5
Reaction score
0
I need the advice about my dilema with my Baja Motorsports DN150 go kart. The kart ran great when I got it and on occasion it would backfire at full throttle (pop thru the carb) almost indicating a potential "miss". Then one day I went to start the cart and noticed it was hard to start. Eventually I discovered that the kart would only stay running when the key switch was "held" in the "start" position. I replaced the corroded key switch and it still does the same thing. Is there an evident part that would show indications of my symptoms? Does the voltage regulator or CDI module factor in? Could a bad ground cause this problem? If anyone has any feedback I would appreciate it. Otherwise I will be stuck with having to pay a shop "by the hour" to diagnose and fix the problem. Urg!

Sincerely,
Brian
 

KieranM

Doin It!!
Messages
1,409
Reaction score
3
Location
Kilkenny, Ireland
Could be the coil, bad connection along the way, corroded wires and as you mentioned a stable ground would be helpful.

Also did you do a spark plug change, and general service when you bought it, clean carb, air filter etc.
 

hotrodhenson

New member
Messages
5
Reaction score
0
Thanks for the reply. I did all of the routine maintenance. The motor runs great if I hot wire the ignition. The problem is that the starter is engaged as well. It is definately an electrical issue. I just dont want to start buying parts left and right to narrow down the issue. Back to the drawing board I guess.
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
I'll try to help you diagnose the problem, how many wires are going to to your Key switch? And what colors are these wires?

Now inspect this key switch wiring harness all the way back (looking for any damaged/crushed spots) and try to describe (or post pics) of where each color of these wires connect to.

Could you get a 12 volt test light or a multi-meter (or anything that will measure DC voltage) to run some simple tests If I explained how?
 

hotrodhenson

New member
Messages
5
Reaction score
0
Well I dont remember what two wires from the key switch but I was able to touch two of them together and the engine would purr like a kitten.
 

hotrodhenson

New member
Messages
5
Reaction score
0
Anderkart, the key switch wires are black, yellow/green, yellow. I have a test light and a multimeter.
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
Its possible that new key switch you bought is either a factory defect or just the wrong switch for your model...

I've never worked on your kart brand but with just 3 wires its a very simple system and I'd guess:

1 is a power input to the switch.
1 is supposed to send this power (only in the crank mode) to activate your starter relay.

And that final wire would probably be used for the key switch to send a ground signal you your engines magneto to kill the engine. If this is the case, the Ignition switch would have to pick up its ground input from being tightly mounted to a clean/rust free metal part of your frame.

You'd clip your test lights alligator clip to a known good ground to test the 2 hot wires function,
and then you can simply move the test lights alligator clip over to your battery's positive post to use the test light for diagnosing ground circuits.

See if you can use this info to do some tests. If you cant figure it out post some pics or describe what these 3 wires go to.
 

shake this

New member
Messages
182
Reaction score
0
Could is be possible that he has the two power wires revirsed?

For an easy example, let's say that we have 3 wires. One wire is ground, 1 wire is hot all the time and the 3rd wire is switched hot only when the key is in the start position. Because the motor runs just fine as long as the key is in the start position, what would happen if he reversed the two "hot" or 12V postitive wires?
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
You may be on to a solution there If he was sold the wrong switch, or if its just been mistakenly mis-wired.
Just using his test light and a jumper wire, we should be able to figure this out.
 
Status
Not open for further replies.
Top