Wheels spin at idle with tc

Status
Not open for further replies.

gixxerkart

Big Boss
Messages
240
Reaction score
0
Location
high desert
Bingo. The rod going to that little black thing on the carb is not moving even though the lever-spring-return all that stuff moves. I know the guvna works cause I just started it and was working things over, I pulled on that rod and the engine wanted to die. So I held it and it did die. What sort of hillbilly sorcery is this?!?!
 

gixxerkart

Big Boss
Messages
240
Reaction score
0
Location
high desert
Tomorrow. I pulled the engine tonight, cleaned an inch of dirt off the mounting plate jackshaft. And cleaned some previous welded garbage done by amateur rednecks. I'm beat. Also I cannot get this dang axle off!!!!! Any suggestions? It's the old yerfdog axle. The bearings are holding the axle in, all bolts are out. It's loose but it won't pull out one side to clear the frame brackets! About to pull my hair out.
 

gixxerkart

Big Boss
Messages
240
Reaction score
0
Location
high desert
Hey they exist. My dads a true redneck and the hot rods he's restored are done right. Then there's the other end of the spectrum- amateurs that are also rednecks. I spent fifteen minutes grinding one weld off. The sad part was it wasn't even holding anything together. It's like they a had an extra stick laying around and decided to practice welding on the floor pan!
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Also I cannot get this dang axle off!!!!! Any suggestions? It's the old yerfdog axle. The bearings are holding the axle in, all bolts are out. It's loose but it won't pull out one side to clear the frame brackets! About to pull my hair out.

Brakes, chain & bearings should be the only things holding the axle on. If they're all disconnected then it should fall off.

The bearings may be a bit tight on the mounts; look for grub screws to the axle & loosen off one bearing only
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Correct me if I'm wrong but the throttle arm is connected directly to the carb butterfly, is it not?

On my kart, yes. With the governor in place, no.

On this link, you can see an almost stock setup. On a stock setup there is a spring from the throttle lever to the governor lever, not a solid linkage.
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
On my kart, yes. With the governor in place, no.

On this link, you can see an almost stock setup. On a stock setup there is a spring from the throttle lever to the governor lever, not a solid linkage.

Understood but, I was referring specifically to the engine in this thred.

the throttle cable is hooked up to a strange lever that according to the honda manual is the throttle lever to control engine speed... wtf right?
so i can move that lever back and forth, but i get no reaction form the motor.
here's pics of the throttle setup:
honda gx160

From this pic, I would assume the throttle arm is connected directly to the butterfly. Therefore, moving it should get some reaction, correct?
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
theres a rod from the carb butterfly to the governor arm, but the arm on the linkage, how does it connect to the governer arm? it dosent, theres a spring missing
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
Thanks, I'm glad the videos are helping.

You've got a strange beast of a kart my friend, someone bastardized a newer Yerf's torque converter and mounted it on your older one. So strange.
 

gixxerkart

Big Boss
Messages
240
Reaction score
0
Location
high desert
Yeah. Story of my life man. The last spider box I owned had the WORST homemade roll cage ive ever seen.we risked it a rolled that kart, things snapped and I was pretty lucky to be alive. That's why this kart will be getting a full work over before it even hits the road.

Frame is completely dismantled and prepped for lots of welding. That bar behind the seat is cracked all the way through at every single weld... hillbilly sorcery for sure.
 
Status
Not open for further replies.
Top