Wheels spin at idle with tc

Status
Not open for further replies.

gixxerkart

Big Boss
Messages
240
Reaction score
0
Location
high desert
Just got a belt put on this go kart. It has a comet 30. I noticed the belt was a little tight when I put it on. Started the engine with the wheels off the ground. At idle they were spinning and when revved the belt rode up high on the driver, almost above it. The driven never opened up. My guess is I got too small of a belt. Went with a 203591.
Driven is a seven inch unit. I believe I measured 7 3/4" from output shaft to jack shaft. Please help. New to karts and tc
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
if the belt rides high on the driver, and doesnt even open the driven then i would think your belt is too long.

do the tires move when its on the ground at idle? its normal for them to move a little bit when suspended in the air but barely
 

gixxerkart

Big Boss
Messages
240
Reaction score
0
Location
high desert
if the belt rides high on the driver, and doesnt even open the driven then i would think your belt is too long.

do the tires move when its on the ground at idle? its normal for them to move a little bit when suspended in the air but barely

I didn't have balls to set the back end down as those tires were really moving at idle. I wasnt sure about belt length. According to comets site I chose the right size
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
By looking at the chart you should see its a 203593 belt you need if you've really measured center to center.

Do you have a Manco Dingo of sorts?
 

gixxerkart

Big Boss
Messages
240
Reaction score
0
Location
high desert
It's a weird yerfdog. According to you it's an early model that a ton of ppl on here have. Perhaps you remember my post?
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
In that case it shouldn't be series 30, are the clutches angled on both sides? 13 degrees.

If so your belt number is an MXT98.

Post pictures man.
 

gixxerkart

Big Boss
Messages
240
Reaction score
0
Location
high desert
It is indeed comet. It is indeed asymmetrical. It is indeed a 30 series with a green spring. I can post a pic here shortly
 

gixxerkart

Big Boss
Messages
240
Reaction score
0
Location
high desert
Post a pic or there is no way we can help you :useless:
i just did pics cause its way faster than stupid youtoob. although if need be i can upload a vid. have another question to ask about same kart but its for the honda motor. i'll ask soon or start another thread.
you demanded, and you have been blessed lol:
this is said kart

heres the driven unit that doesnt open up when running

clutch at rest

the entire assmembly


now my motor question is this: when i started this thing i immediately noticed the throttle cable does nothing, it doesnt rev the engine, if i slid the choke over once warmed up the thing wanted to rocket down the driveway. the throttle cable is hooked up to a strange lever that according to the honda manual is the throttle lever to control engine speed... wtf right?
so i can move that lever back and forth, but i get no reaction form the motor. so i left it alone and watched the belt at idle (with the choke on) all of a sudden the engine revs outta control?!?!?!? i shut it down went inside and cried myself to sleep (why do i mention these things?:furious2:)
here's pics of the throttle setup:
honda gx160

top view
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
You see the spring in the 2nd pic? under the fuel tank? connect that to the throttle lever by the screw with the spring on it. Tell us how it works out.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
big one under gas tank. I may be wrong, but your issue appears to be that there is no linkage between the governor lever and the throttle lever. The stock linkage is a spring.
 

gixxerkart

Big Boss
Messages
240
Reaction score
0
Location
high desert
Ok. That spring is attached under the lever arm to the lever arm. But what about the rod that connects to a little piece of the carb, and then runs under tank to an armature that mysteriously disappears? What's that thing for?
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
basically, when you pull the throttle lever, this pulls a spring, which pulls the governor linkage under the tank, which pushes that rod, which rotates the black butterfly lever on the carb. If the governor kicks in, it overrides the spring and reduces the RPM
 
Status
Not open for further replies.
Top