Vertical Shaft conversion to Horizontal Shaft

Status
Not open for further replies.

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
Alright guys, last night, I was in my garage just cleaning up, and I had an old vertical shaft engine sitting on my shelf. I decided, what the heck, why not just convert it. So I drained the oil, took crank case off, and started checkin it out. Well, I was planning on putting an oil slinger in it, but there is absolutely no room.

So, here is what I was thinking of doing. Why don't I just put enough oil to where I wouldn't need one. If I put about 2 quarts in it, it would fill it up just over the crank shaft. I could always use a minor additive of 2-stroke oil also to make sure the cylinder stays lubed up. What do you guys think?
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Increasing the amount of oil in the crankcase in turn increases the amount of pressure exerted on seals, gaskets, rings, etc. If you want to blow out every seal, go ahead.

It wouldn't be hard to fabricate a spoon shaped dipper with a flat handle (for lack of a better word). Mounted across the big end cap & protruding only about 1", it should do the trick. If there is that little amount of clearance, the big end cap would be dipping in the oil.

Post some pics of the crankcase so we can work on a solution for you
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
Does the bottom of the conrod come that close to the 'case?

Increasing the amount of oil in the crankcase in turn increases the amount of pressure exerted on seals, gaskets, rings, etc. If you want to blow out every seal, go ahead.

It wouldn't be hard to fabricate a spoon shaped dipper with a flat handle (for lack of a better word). Mounted across the big end cap & protruding only about 1", it should do the trick. If there is that little amount of clearance, the big end cap would be dipping in the oil.

Post some pics of the crankcase so we can work on a solution for you

I have already tried mounting a dipper in there, but there is literally no clearance to put one. The conrod, when closest to the cylinder, is maybe a 1/16" to 1/8" away from the cylinder. I had about a 22ga. piece of sheet steel in there to spoon it up. I was shaping it around the the cylinder with it attached to make it easier, but, it just flattened it down on the conrod.

To tell you the , I don't give a crap if I blow the seals or anything, this is just like a toy to me to mess around with. I have a few other engines that mean much more to me, but if this works, then I can do it with my other vertical shaft engines.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
As the dipper would (and should) protrude from below the conrod cap, cylinder clearance should not be an issue- clearance to the 'case should be.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Well- that's how all the horizontals do it! Do a google image search on rods for Hondas, clones, Briggs, etc- should give you a pretty clear idea.
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
Well- that's how all the horizontals do it! Do a google image search on rods for Hondas, clones, Briggs, etc- should give you a pretty clear idea.

I've seen many of them in firsthand experience. But they always had clearance. I will tear it back apart tomorrow and look at everything, probably figure something out.
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
Converting a V engine seems pretty sketchy. How does the flywheel situation work afterwards? I thought on a vertical engine, they weigh less since they are placed differently. How does this affect the momentum of the wheel?
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Converting a V engine seems pretty sketchy. How does the flywheel situation work afterwards? I thought on a vertical engine, they weigh less since they are placed differently. How does this affect the momentum of the wheel?

It's not so much a matter of them being placed differently, as it is a matter of weight. Many verticals (most specifically lawnmower verticals) use significantly lighter flywheels. This is done from the factory because of the additional rotating mass of the mower blade. Without the blade, these engines can be harder to start.
 

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
that would have been nice to know when i rebuilt my lawn mower engine i ended up throwing it away :roflol:
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
i just thought of something..... what if you put a large pipe fitting somewhere on the crank case and ran a 1" or so diameter tube up to a closed can that has the same volume as the amount of oil you need to add to submerge the con rod? more complicated than a dipper but if you have no possible way of adding one.....
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
i just thought of something..... what if you put a large pipe fitting somewhere on the crank case and ran a 1" or so diameter tube up to a closed can that has the same volume as the amount of oil you need to add to submerge the con rod? more complicated than a dipper but if you have no possible way of adding one.....

Good idea, but if I add more oil, it does the same thing basically.
 
Status
Not open for further replies.
Top