Total Newbie, need help!

Status
Not open for further replies.

trgerman76

New member
Messages
10
Reaction score
0
OK, I got it working!!! I put the screw in and kept adjusting it until it idles and didn't stall. Based on you comment above that probably didn't make any difference! Just dumb luck! I took the kids around the block a few times. I'll try it again tomorrow when it's light out. Thank everyone for your help!!! There are two really happy kids in my house tonight!
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
OK, I got it working!!! I put the screw in and kept adjusting it until it idles and didn't stall. Based on you comment above that probably didn't make any difference! Just dumb luck! I took the kids around the block a few times. I'll try it again tomorrow when it's light out. Thank everyone for your help!!! There are two really happy kids in my house tonight!

Hey, I am glad you got it sorted out!

which screw exactly did you tinker with? I am having trouble identifying the on toystory is talking about.

Have a look at the pic. It is this one.
 

Attachments

  • go-kart004.jpg
    go-kart004.jpg
    96.6 KB · Views: 14

Calsa

New member
Messages
9
Reaction score
0
Hi Trgerman76, I am working on that exact same engine B&S 136212 and am having a heck of a time getting the carb/gov linkage to go back together correctly. Any chance I can get you to take a few shots of the area right under the tank. Maybe a shot from the side taken right underneath the tank as I am trying to see how the linkage and springs all line back up on the backside of the mounting bracket that holds the fuel tank on. Getting a good shot might be tricky as its dark and partially obstructed by the flywheel housing but one good shot will tell me how to get that lower linkage back together.
 

Calsa

New member
Messages
9
Reaction score
0
Hmm, I am still not seeing what makes the governor wire move. The only thing connecting the throttle cable plate to the governor arm is that spring, unless I am missing a wire. But the spring can not push the governor wire up. Thoughts?
 

slideways

New member
Messages
575
Reaction score
6
The highlighted screw is the IDLE speed screw. Has nothing to do with the governor. Makes sense that the engine wouldnt run right when he backed it off. He was just turning the idle down so far that it wouldnt run. When he turned it back in it would idle again. If the original poster has his throttle linkage setup in the stock "Fun Power" Briggs configuration then his issue is with the linkages under/behind the gas tank to limit the throttle.

I HATE Flatties and even i remember that.
 

FlatFootRacing

Speed Freak
Messages
52
Reaction score
0
Location
Easley, SC
That is the Idle adjustment screw! It only sets where the engine will idle at! Screw that in and it opens the butterfly in the carb, unscrew it and it closes it up! Looking at your clutch, the bushings appear to be worn pretty badly! The clutch bell housing should not be tilting to one side that much! You may (only if you feel the its neccesary to) replace the clutch! Tractor supply has them pretty cheap! And soak that chain in some oil for a day or so! Or replace it!
 

Calsa

New member
Messages
9
Reaction score
0
landuse, thanks for the pics. In the first picture you posted, what does the lower end of the wire with the red arrow pointing up connect to? Does it connect to the governor arm extending out of the engine, or to the back side of the pivoting piece that the accelerator cable connects to on the fuel tank mounting bracket? The whole back side of that assembly is what has me tripped up right now (what the lower end of the wire arm connects to and the governor arm spring connection points).
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
landuse, thanks for the pics. In the first picture you posted, what does the lower end of the wire with the red arrow pointing up connect to? Does it connect to the governor arm extending out of the engine, or to the back side of the pivoting piece that the accelerator cable connects to on the fuel tank mounting bracket? The whole back side of that assembly is what has me tripped up right now (what the lower end of the wire arm connects to and the governor arm spring connection points).

The wire with the arrow pointed upwards connects to the pivoting piece which has a red arrow pointed to the left.
 

Calsa

New member
Messages
9
Reaction score
0
Ah, thanks. I connected it to what appeared to be a bushing on the end of the governor arm. I'll make the swap when I get home and see if this works better.
 

Calsa

New member
Messages
9
Reaction score
0
No luck so far. I did find this post:
http://www.diygokarts.com/vb/showthread.php?t=4473
VultFan has the exact same linkage setup, and right now mine is exactly hooked up like his photos, with the exception that my spring is fully attached to the "H" bracket on the Governor Control Arm.

But what I am not understanding, is what connects the throttle control bracket mounted under the fuel tank (where the spring attaches to the throttle plate) to the governor control arm (where the spring attaches to the "H" piece. Right now the only thing connecting those two pieces is the spring itself, but I think I need a wire or something to connect them too. Otherwise there is seemingly nothing to move the wire that comes off the governor control arm and connecting to the butterfly valve up top.
 

Calsa

New member
Messages
9
Reaction score
0
I have uploaded a short video to youtube of my current governor setup in hopes that it helps solve this problem.

Link to vid: http://youtu.be/uuWf9DNaGxc

Let me know if you have any ideas as to what might be missing, or whats wrong with my setup.
 

Calsa

New member
Messages
9
Reaction score
0
OK, got it. For future reference if anyone has an B&S 136212 (or similar), hook the governor up as shown in the attachment and you are good to go. This had me tripped up for a week as until you fire the engine this setup wont work. However, as soon as the engine is running forces the governor control arm up and then pushing the gas pedal pulls it back down opening up the throttle.
 

Attachments

  • 136212_1026_E1_Governor_Setup.jpg
    136212_1026_E1_Governor_Setup.jpg
    453.6 KB · Views: 18

Calsa

New member
Messages
9
Reaction score
0
Yeah, it definitely seems like an odd governor setup, not being able to see that it's working unless the cart is running in all. Ah well, all fixed now. Time to Craigslist the cart as I leave for two years of volunteer work overseas Monday! Thanks for everyones help.
 
Status
Not open for further replies.
Top