Total Newbie, need help!

Status
Not open for further replies.

trgerman76

New member
Messages
10
Reaction score
0
I just brought home a go kart for my kids, bought it on craigslist. They rode it for not even 5 minutes and then something happened. My son had just started applying the gas and the cart suddenly stopped and the wheels locked up. I tried to pull the cord to get it started again but it would not let me pull it. I had to carry it back to the house with my wife.

The guy I bought it from said he's never had problems like this before, but he just got it a few weeks ago. He did say that he somehow reduced the speed of the go kart to about 5-7 mph by loosening some screw under a filter. I couldn't find the screw.

Anyway, I can't figure out why the wheels are locked up and why I can pull the cord to get it started. I am searching online and can only find information saying that it may be a stuck clutch. If this is the case, what do I do to unstick it!?

Any help would be greatly appreciated! My kids are heartbroken and now the guy is not answering. Here is some information I got off the go kart;

Briggs & Stratton Fun Power
Model: 136212
Type: 0026 01
Code: 960912YA

It also says Comet 5005 on the chain cover.

Thanks so much for any help you can offer!
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
posting a picture of the engine and driveline would help. Now- With the rear of the kart off the ground (on blocks) can you pull the cord? Do the wheels turn when you do that?
 

trgerman76

New member
Messages
10
Reaction score
0
toystory-4wd - Ok. I will take some pictures of the engine and the Clutch and post them. I did raise the rear and try to start it and it the cord will not pull and the left wheel is completely unmovable and the right moves very slightly.

slideways - I did not check the oil. The guy who sold it to me did turn it on and run it to show that it ran. I didn't think to check the oil.

b-man - I don't know. I did manage to find the user manual though. http://bsintek.basco.com/BriggsDocumentDisplay/mssAIN-K_ny7tH217FzoPu.pdf. I am just starting to even know what the clutch looks like!

Thanks all for replying!
 

trgerman76

New member
Messages
10
Reaction score
0
Any advice on how to remove the chain? I just tried to loosen the bolt at the end of the clutch and it moved the wheel slightly, but not much. The chain itself is incredibly tight. I don't know if that is normal.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Try looking for a master link on the chain- a clip you can pry off with a flat screwdriver and disassemble the link. Failing that, loosen motor mount bolts and slide engine until there is sufficient slack in the chain to slip it off. If engine mount holes are not slotted, remove mounting bolts completely.

Edit- chain should NOT be incredibly tight. This is a problem that WILL cause other problems.
 

trgerman76

New member
Messages
10
Reaction score
0
Once I remove the chain, is it safe to try to start the motor to see if it will start? just thought I would ask before doing it!
 

Jake.B

New member
Messages
495
Reaction score
0
Location
California-USA
Im not an expert on clutches but the rust doesn't look so good the clutch housing if its on the outside its probably on the inside it makes me think a stuck clutch.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Yeah- go ahead and give the cord a tug- tells us if the engine will rotate. Also note whether wheel(s) will rotate freely at this point.
 

trgerman76

New member
Messages
10
Reaction score
0
Sorry for the late reply. It's been a hectic day. I got the chain off and the engine started just fine. The clutch is spinning but it seems very loose. All the pieces are not attached to each other very good. This may be normal, I am not sure.

The wheels are moving great. No issue there. Once the chain was off everything loosened up.

It really does look rusty!

Now, should I try to reassemble and see if it runs with the chain in place? Or it it obvious that the clutch is bad? I can take a video of the clutch to show how loose it is.
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
If it were me I would put everything back together, making sure that the chain is not as tight as what it was originally. I think that was your problem. Maybe lube the chain as well. See if everything then works OK and the kart rides OK. If everything is good, then I wouldn't worry too much about the clutch. It is quite rusty though. You could maybe take the clutch housing off and see how rusted it is inside and clean that up.

If you decide to buy a new clutch, they are not too expensive (maybe $30 or so).

Just as an afterthought....the clutch could seem loose from the forces that the tight chain put on the clutch
 

trgerman76

New member
Messages
10
Reaction score
0
That sounds like a good plan. I will work on that today.

The guy I bought it from mentioned that he messed with something to make the cart go slower. He said if you take off the cover where the gas filter is (on top of the engine), then remove the filter, there are screws that you can loosen or tighten in there. I took it off but didn't find any screws. Any idea what he meant. I think it may be what is causing problems. I read somewhere that you shouldn't limit's it's rpms.
 

trgerman76

New member
Messages
10
Reaction score
0
Here are some picture from underneath the air filter. I removed it and the metal casing it was in. I assume this is where he messed with the settings to slow the go kart down to 5mpg from about 20mph. What can I do to undo it! Of course he is not returning my calls.





 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
See that screw in the first picture with the tightly wound coil spring wrapped around it? That's the governor adjust screw- back that puppy right out, and your maximum RPM will increase to a governed 4000-4200 (ballpark) RPM. FYI- The way he's got that thing cranked it, I wouldn't be surprised if the clutch is fired. That is a BAD method of limiting top speed, as the clutch spends it's life slipping and cannot attain lockup RPM. Slipping=heat, and heat kills centrifugal clutches. For your own knowledge, use GEARING to limit top speed, NOT RPM via the governor adjust screw.
 

trgerman76

New member
Messages
10
Reaction score
0
OK. I took the screw all the way out and that made the engine run pretty badly. So I put it in about half way and it runs better but still stalls after I let up on the gas. Is there an certain amount the screw needs to be tightened?
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
No. That screw ONLY sets the maximum throttle point (where the governor limits). Any POOR running is an unrelated issue. Other settings may be off, or your carb may be in need of a cleaning.
 
Status
Not open for further replies.
Top