torque converter help

Status
Not open for further replies.

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
What are you doing with the kart, what top speed, what weight and wheel size, what are you hoping for acceleration and wear?
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
Would u recommend a high performance centrifigal clutch intead?

That depends on your kart, drivers weight, and where and how you'll be riding.

A T/C would definitely be better for a heavy offroad kart that's climbing hills and doing a lot of low-speed/stop and go type driving.

On the other hand I'd prefer a high quality centrifugal clutch for a lighter race kart that runs wide open around a flat paved track, streets or parking lot.

If you post more info/pics of your kart, weight and where you'll be riding we could give better advice.
 

JBkartman

New member
Messages
29
Reaction score
0
The kart will be mainly used for gravel road long distance and maybe some sand. The kart is 8 ft long and with me probably weights around 500lbs roughly. The tires are around 15 inches.
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
It really sounds like a 40-series T/C would be your best choice, but if you want to try a 1" bore centrifugal, the most heavy duty model you'll find is the Noram Enforcer. Its available with #35 or #40/41 pitch drive gears here: http://www.out2win.com/catalog/noram_enf.html

With 15" back tires, a 10-tooth clutch might be your best choice.

How many teeth does your axle sprocket have?

We'd also need to figure out what pitch your axle sprocket is, heres a chart if your not sure:

 

JBkartman

New member
Messages
29
Reaction score
0
I have a 41 chain and sprocket not sure on rear sprocket tooth count. would the norman clutch be good on takeoff though. like move it with ease with me in it because im not sure how to make a jack shaft from scratch even after viewing forums and examples. It seems too complicated.
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
A tourqe converter would always give better acseloration, but If you had a large enough axle sprocket, a good cintrifigal could give fairly good acseloration.


You might take a look at all these jackshaft pics: http://www.google.com/search?q=go+k...ct=mode&cd=2&ved=0CDwQ_AUoAQ&biw=1024&bih=556


We could help you instal a jackshaft and T/C, we'd just need to see some pics of your karts axle area with your engine.
 

JBkartman

New member
Messages
29
Reaction score
0
I think the bracket that attatches like these "http://sporting-goodsonline.com/go-kart-cart-yerf-dog-jackshaft-mini-bike-clutch-mount-.html" would be my best bet because i have used one of these before and it is simple but it wont fit on this engine, but like i said i will post pics of the kart.
 

JBkartman

New member
Messages
29
Reaction score
0
I did not mount the new engine yet. This is the older engine that was on prior.
 

Attachments

  • IMAG1139.jpg
    IMAG1139.jpg
    141.5 KB · Views: 5
  • IMAG1140.jpg
    IMAG1140.jpg
    112.2 KB · Views: 6
  • IMAG1141.jpg
    IMAG1141.jpg
    125.7 KB · Views: 10
Status
Not open for further replies.
Top