torq converter help

Status
Not open for further replies.

kartmonster13

New member
Messages
82
Reaction score
0
ok guys i need some help i just got this nice little screamer cart its a streaker cart with a fun power 5hp briggs that runs great it has live axle and a disc brake as well as the tav 30 converter no thus being said after 2 days of having fun my drive sproket that goes to the main axle sproket is shot its worn down to almost nothing and just barely made it home now i need to know how to change this gear ..do i have to take off the drive end of the converter? wich i just read is not an easy thing to do and all i have for a gear is one off an old js and is a bigger gear please let me know what i can do thanks :confused::furious2::mad2::confused:
 

kartmonster13

New member
Messages
82
Reaction score
0
ok so i just checked its an original tav 30 series tc and i need to change part #24 drive gear do i have to take the whole back part of the pulley clutch apart or does that just come off to replace the sprocket wow just realized cant spell but anyways mfg supply has the replacement gear for $20 and then 6.99 for shipping im wwondering can i just use a 13 tooth engine sprocket instead or just go with the replacement part it would be cheaper and quicker but i want it to last i just got this cart
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
1. Remove plastic cover,
2. Remove nut on jackshaft.
3. Remove driven and sprocket. Remember the order and orientation- there are spacers too.
You may need to undo the bolt holding the driver on and remove that too.

However, the sprocket should not wear that quickly. Pics?
Maybe you are using the incorrect pitch chain or something?
 

kartmonster13

New member
Messages
82
Reaction score
0
ok i will upload pics in a few mins but after a close look the the rear part or the driven i guess has a 20 stamped on it and i was reading on here about the 3 dif holes for the spring and its in the first one no that being said the streaker axle gear has 54 teeth and the gear off of the TC has only 9 teeth im not new to carts but new to fixing them lol i have my old hard drive murray cart and its live axle has 36 teeth and the jack shaft out is 26 teeth and the jackshaft in has 10 teeth now after looking again the streaker axle sprocket is pretty worn down and looks more like a ninja star lol i will post the pics in a few so everyone can see thanks for the info ...now with that gear ratio how fast do you think it will go if i put the motor and TC on the JS on the hard drive frame ?
 

kartmonster13

New member
Messages
82
Reaction score
0
pics of the streaker and the tav TC

ok here are the pics
 

Attachments

  • 100_4874.jpg
    100_4874.jpg
    235.7 KB · Views: 10
  • 100_4875.jpg
    100_4875.jpg
    147.6 KB · Views: 7
  • 100_4876.jpg
    100_4876.jpg
    147.9 KB · Views: 9
  • 100_4877.jpg
    100_4877.jpg
    110.5 KB · Views: 7
  • 100_4878.jpg
    100_4878.jpg
    105.4 KB · Views: 9

kartmonster13

New member
Messages
82
Reaction score
0
the rear tires are 16 x 7.5 x 8 and the fronts are 15 x 6 x 6 im also having trouble steering it basically wants to plow the dirt when i turn and i also tried a set of really small ones but that made no difference im wondering if it has something to do with where the spring is on the TC or maybe its just because the cart is only 5 and a half ft long i want to set this p so i can go fast but yet would love to be able to do doughnuts i live on a dirt road but when i take it on the road it sticks like glue and is pretty fast turns on a dime but when i go back to the dirt it just wants to go straight im lost on this
 

kartmonster13

New member
Messages
82
Reaction score
0
more pics of the streaker cart and of my hard drive

here are some more pics off the new cart and of the old hard drive murray that im building
 

Attachments

  • 100_4736.jpg
    100_4736.jpg
    258.5 KB · Views: 14
  • 100_4735.jpg
    100_4735.jpg
    218.3 KB · Views: 14
  • 100_4881.jpg
    100_4881.jpg
    277.2 KB · Views: 4
  • 100_4880.jpg
    100_4880.jpg
    245.1 KB · Views: 79
  • 100_4879.jpg
    100_4879.jpg
    243.6 KB · Views: 7

kartmonster13

New member
Messages
82
Reaction score
0
ok so after looking at the northern tool and MFG supply web sites my TC should have a 10-12 tooth gear for the #35 chain and it has a 9 tooth sprocket on it and is prob for a 40 or 41 chain so i think that was the problem with it chewing up my sprockets now my question now is can i take off the 36 tooth sprocket off of my hard drive axle and use that on the streaker axle and what type of gear ratio would that give me and what speed would i be looking at
 

kartmonster13

New member
Messages
82
Reaction score
0
more pics of the TC and 9t sprocket

ok here are some pics of the 9 tooth sprocket and pics of the TC
now i measured the shaft for the 9t and its a 5/8 shaft im lost i need to order that new sprocket and want it to be the right one considering im on a tight budget and cant reorder if its wrong the new part is a 12t sprocket will that work ? :mad2::confused::confused:
 

Attachments

  • 100_4886.jpg
    100_4886.jpg
    108.3 KB · Views: 6
  • 100_4889.jpg
    100_4889.jpg
    115.4 KB · Views: 3
  • 100_4888.jpg
    100_4888.jpg
    110.2 KB · Views: 3
  • 100_4887.jpg
    100_4887.jpg
    60.3 KB · Views: 5

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Measure the chain pitch and sprocket pitch.
That is not normal! Did you have the chain really loose? 1/4"-1/2" is good.
 

kartmonster13

New member
Messages
82
Reaction score
0
are there any other places i can get these parts from cheaper? its only 26.49 with shipping and $20 for a new 54t sprocket but i want more speed and be able to blow doughnuts with it ,,if not im looking to put the 5hp motor and TC on my murray hard drive frame but it has a jackshaft already on the frame as you can see in the pics can i use that and the TC ?
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK

kartmonster13

New member
Messages
82
Reaction score
0
oh ok got it its a 1/2 pitch for the chain and a 5/8 width for the sprocket sorry bot that still new to these forums i think that link will def help me out now thanks so much
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
A #41 sprocket would work, or possibly a #40, I dunno because you got the sprocket width horribly wrong... ;) should be more like 1/4". Not a #35 sprocket.

Sorry, I know it isn't very helpful, but I really can't be arsed to work out gear ratio's and speeds now, cos I am about to go to bed!

What you do though-
(Jackshaft input/ tc output) x (axle sprocket/ jackshaft output)

Your ratio is 1: this number. E.g. 1:6 or 1:4.5

Use this
Www.diygokarts.com/speed-calculator.html

Then put in the number you got from the calculation in as the axle sprocket size and the clutch size as 1.
Enter your tyre diameter and engine rpm (usually 3600)

You probably want to keep speed under 30. I dunno what engine you have.
However if your kart is slow and cannot do donuts, you are unlikely to be able to make it fast and spin tyres with a gear change.
However, my kart can do donuts after changing the steering- search for camber, caster and Ackerman on this forum.
 

kartmonster13

New member
Messages
82
Reaction score
0
ok got the new 12t sprocket in i also changed the spring position to the 2nd hole and tried it,, tho it was a lil quicker top speed i decided to try it back on the first hole and now it does doughnuts fn sweet!! still having trouble steering and noticed the left spindle is messed up
 
Status
Not open for further replies.
Top