Tecumseh OHH50 help

Status
Not open for further replies.

zeeker

New member
Messages
4
Reaction score
0
So I'm doing some repair on my favorite bar lady's kids OLD Manco go cart. While I'm waiting on sprocket and clutch parts to drop in my mailbox, I thought I'd get the motor running. (It hasn't run in ten years.) It's a Tecumseh Power Sport model
OHH50 69167G. While smoking out the throttle cable and related stuff in the back I noticed the governor or throttle spring as Tecumseh calls it, just kind of hanging there, so I bought a new one! Well, I can see where one end hooked but I don't have a clue where the other end goes. Is this spring necessary? Am I missing something else? (another spring) I'd be grateful if somebody could explain it or shoot me a picture.
Thank You.............zeeker
DSC02188.JPG DSC02185.JPG

DSC02187.JPG DSC02206.JPG
 

slideways

New member
Messages
575
Reaction score
6
Looking at your pictures everything seems ok. The big spring in the first picture (not counting the one of the kart) should be there and is like the cable return spring you feel against your foot. The long wire spring pulls against that governor arm and when the governor engages it will pull it against to close the throttle butterfly. The one it looks like you took off would override the governor too much IMO and may blow up the motor. Good to see you got a replacement for that one. Tecumseh always had a long piece of wire around that spring and going back to that tang that sticks down on the throttle plate. I never knew why it was needed but i think it works fine without it.
 

zeeker

New member
Messages
4
Reaction score
0
Hey slideways, thank you so much for your response. I think maybe I didn't explain myself very well. The governor spring is the ONLY connection from that right hand panel to the engine throttle by way of the governor link. Am I missing something? Where I have hooked it (shown in pics) slightly overpowers the governor but I see nowhere else to put it that would open the throttle. The original bent up one was only hooked to the governor link when I got it. I cleaned the carburetor (it was spotless when I took it apart) and there is very little play in the throttle shaft but the motor surges pretty bad (runs up and down on the governor). I sprayed carb cleaner around all the mating gaskets but there was no change. I bought the spring from Tecumseh so I'm wondering if, because it's a gas pedal cable controlled kart, Manco used a different setup? Maybe I have the wrong spring? Do you have any more advice for me?
Thanks again...........zeeker

DSC02210.jpg DSC02211.jpg DSC02212.jpg
 

slideways

New member
Messages
575
Reaction score
6
It actually goes in the hole we cant see in the picture. The long ear sticking down with the hole going side to side not front to back like we would see. It only takes a little bit to activate the governor/throttle linkage. Otherwise you would barely have any pedal travel. On the Dingo i always remember that you have no gas pedal until you are almost 3/4 of the way down on it for this reason.
 

zeeker

New member
Messages
4
Reaction score
0
Hey slideways, thanks again for the response. I see the hole your talking about. I would say FOR SURE that I have the wrong governor spring. It looks to be about an inch too long. Do you have any clues as to where I might get the proper one? Manco? Tecumseh? Part number? Picture?............Thanks............zeeker
 

slideways

New member
Messages
575
Reaction score
6
What does it look like when you put it in the correct hole? Pic? Does the gas pedal work at all then?
 

anderkart

Moderator
Messages
6,432
Reaction score
393
Location
Surprise Arizona USA
Hey slideways, thanks again for the response. I see the hole your talking about. I would say FOR SURE that I have the wrong governor spring. It looks to be about an inch too long. Do you have any clues as to where I might get the proper one? Manco? Tecumseh? Part number? Picture?............Thanks............zeeker


The correct spring and linkage rod your missing is
available here:--> http://www.quickieparts.com/tecumseh/tecumseh-throttle-linkage-36711-and-37111.html

________________


You'd instal them like these pics:



More pics here:--> http://www.menintools.com/linkage.html


 

zeeker

New member
Messages
4
Reaction score
0
Thank You, Thank You, Thank You. That is exactly the information I needed. I guess the spring I bought was the right one after all but I only bought half of what I needed. AND, I don't think I would have EVER figured out how they went on without those pictures. The Manco will live again!
 
Status
Not open for further replies.
Top