Tecumseh OHH50 68077G

Status
Not open for further replies.

TorqueRanger

New member
Messages
257
Reaction score
1
I pick up a gas power air compressor running a Tecumseh OHH50 68077G.. But I found the carb full of crap and needs to get rebuilt or heavily cleaned ... I am not sure if it worth rebuilding or just buy a aftermarket replacement from ebay ??? I was going to rebuild the carb but found out that I need a special tool in order to rebuilt it unless you guys have some tips or tricks up your sleeve...


It needs a
Primer bulb
Bowl gasket
Bowl nut
Carb rebuild kit


Thanks Ahead of Time
JAy
 

TorqueRanger

New member
Messages
257
Reaction score
1
Here it the tool

The problem is that the engine has been outside for some time and had old gas in it and is now gone by the time I got it... So the carb has some corrosion inside and I have clean some of it up but I am not sure it's worth the effort ... I am pretty much replacing almost everything inside the carb too .. My problem is that I can get a new carb off ebay for $40 bucks with shipping included or buy the parts and the tools for about same price but I will have the knowledge and the tools to do the job again if I have to do it again but my thing is that this is the only Tecumseh engine I have , so is it really worth it????
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
/There are a few of us on this forum that prefer Tecumseh products.
It's common knowledge that they do produce more HP per pound than an equivalent B&S.

The carbs (a Walbro design) on these engines require more maintenance than what might be considered normal. Carb must be completely drained of fuel if stored for a month or more.
It's been my experience that once corrosion starts, it doesn't stop. The corrosion shows itself as little white spots on carb body and almost resembles a fungus.

If it were my engine I would bite the bullet and get the new carb...provided that the engine in question is in good/excellent condition.
As far as the tool is concerned...I've rebuilt a fair amount of Tecumseh/Walbro carbs and never needed this tool.
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
i believe the tool your talking off is the one to remove the needles seat. many just substitute this with a paper clip. you can go with aftermarket carb and get much more power from the engine, but it will have no placement for your old governor linkage and the internal governor must be removed.
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
it will have no placement for your old governor linkage and the internal governor must be removed.
Well...maybe. Direct replacement may/may not be available.
Also, there are "service" carbs that require the use of removable parts from old carb so that it will work as well as the original.
 

TorqueRanger

New member
Messages
257
Reaction score
1
/There are a few of us on this forum that prefer Tecumseh products.
It's common knowledge that they do produce more HP per pound than an equivalent B&S.

The carbs (a Walbro design) on these engines require more maintenance than what might be considered normal. Carb must be completely drained of fuel if stored for a month or more.
It's been my experience that once corrosion starts, it doesn't stop. The corrosion shows itself as little white spots on carb body and almost resembles a fungus.

If it were my engine I would bite the bullet and get the new carb...provided that the engine in question is in good/excellent condition.
As far as the tool is concerned...I've rebuilt a fair amount of Tecumseh/Walbro carbs and never needed this tool.

i believe the tool your talking off is the one to remove the needles seat. many just substitute this with a paper clip. you can go with aftermarket carb and get much more power from the engine, but it will have no placement for your old governor linkage and the internal governor must be removed.

Well...maybe. Direct replacement may/may not be available.
Also, there are "service" carbs that require the use of removable parts from old carb so that it will work as well as the original.

I'd say go ahead and take a shot at resuscitating the existing carb first, if it isn't too far gone. If it fails, you're only out a bit of time.
Is there a real difference between an oem carb or aftermarket???
I am trying to get max reliability ,so it will run everytime and I don't have to play with it in order to make itrun..
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
Is there a real difference between an oem carb or aftermarket???
Not in the way they function. The problem with most aftermarket carbs is that they are Chinese and not rebuild-able. That is to say that a Tecumseh rebuild kit will not work (some exceptions) on a Chinese carb.
 
Status
Not open for further replies.
Top