Tecumseh 5HP won't start warm (sometimes)

Status
Not open for further replies.

dave1701

Good for 100,000 Miles
Messages
1,069
Reaction score
1
Location
MICHIGAN
This has been the only problem with this motor. Sometimes, when warm, it doesn't start. If I shut it off after 10 minutes of riding, then come back to it (usually under 5 minutes) it doesn't start or make in indication of trying to start. It is like I have the switch turned to off. I pull it about 20 pulls and it eventually starts. I've had this problem since this motor was brand new. It seems as if it did it MORE when it was brand new than it does now. It used to happen every time.

Now it only happens occasionally (usually when I'm bragging or showing off my kart, of course). The motor doesn't even try to turn over though, until I wait a while. Other than this, it works flawlessly. When it is cold, and usually when it is warm it starts on the first or second pull. However, occasionally it will do this.

It is a pain. I don't THINK that it is overheating, because it only does this sometimes and it runs perfectly when it is on. Plus, when it is running, it runs great.

Any ideas?

This is my motor:



 

Badot

New member
Messages
677
Reaction score
3
I'm no carb expert but I would think you should see if you can lean your idle mix a bit...

Does your engine idle poorly once warmed up though, and/or can you see a bit of smoke coming from the muffler?
 

Badot

New member
Messages
677
Reaction score
3
Valve lash maybe? If the valves expand and hold the ports open just a tad I can imagine you could have those problems.
 

dave1701

Good for 100,000 Miles
Messages
1,069
Reaction score
1
Location
MICHIGAN
It just did it again today. I waited 5 minutes and it started up first pull. I'll check the plug when I get a chance. Don't why that would be the problem though.
 

sexyvicta

New member
Messages
806
Reaction score
2
^ I've heard of it being a common problem on honda lawnmowers factory fitted with a certain ngk plug. When it gets hot it stops working. Let it cool down and then it will restart only to stop again after a few mins. For the price of a plug i would definatly try that
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
It just did it again today. I waited 5 minutes and it started up first pull. I'll check the plug when I get a chance. Don't why that would be the problem though.

i meant to say the coil gap. but its always good to check anyways...

im thinking more of valve lash because when its hot the valves wont seat right because they get a little longer from heat expansion.
 

sexyvicta

New member
Messages
806
Reaction score
2
^ nah i doubt its a valve problem as its been doing it since brand new.

I would say you have a faulty part...most likely spark plug or the magneto. It happens.

Or maybe its a carb problem like the hinge on the float is jamming or the needle is sticking? iduno.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
my neighbors briggs mower (2003) does this as well.

so its most likely

.ignition
.head not sealed?
.valve train too tight

i dont know that it would be a carb problem because a carb doesnt get warmed up.
 

dave1701

Good for 100,000 Miles
Messages
1,069
Reaction score
1
Location
MICHIGAN
Anyone? This same **** thing happened today TWICE. So far. Takes over 20 pulls, or I have to wait for it to cool down. One time when it finally started, it blew out a small bit of smoke. Could that might have been from the pulling 20+ times? Or does that say that my mixture is too rich? But why would it only have problems when it's being started warm?
 

dave1701

Good for 100,000 Miles
Messages
1,069
Reaction score
1
Location
MICHIGAN
I haven't done much messing with carbs before, but I'll look about in there when I muster up the courage.


Addendum to post #17.
Very possible coil is grounding/shorting out due to heat soak.


On a new motor? Is there any way to test that theory? So I should check for a spark the next time this happens?
 
Status
Not open for further replies.
Top