tech' 2 stroke snowblower motor?

Status
Not open for further replies.

firekiller52

Flat Head Kinda Guy
Messages
58
Reaction score
0
Location
nj
hi guys, my dad brought home an engine from a 2 stroke toro snowblower(rubber pattle kind) and just wondreing how anybody hooked everything up, like the carb sits level at 45 degrees turned,(from the cylinder) and theres 4 bolts coming out around the crankshaft

also its got a little baby crank, like 5/8ths mabe, any ideas for a clutch other than a sleeve
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
For quite some time I was trying to get my hands on one of those to use for a kart or minibike. I'm trying tho remember- I think they are Suzuki engines.

Anyway, the engine will work in any orientation as long as you fab/modify an intake to allow the carb to sit level.

I believe you can get 5/8" centrifugal clutches.
 

firekiller52

Flat Head Kinda Guy
Messages
58
Reaction score
0
Location
nj
ok i have a smaller model i use at work, and the engine is a tech'(cant spell it haha)
and i belive this is a beefed up model, i know it will run in any position but 45 degrees is the easyest since thats where the carb sits now, just wondering if any has tryed this or if im wasting my time

if i cant find a clutch cheap, i know a machenest that can make a collar for the crank for me
idk, plus any 2 stroke info on these things anybody can give me, ill do anything with a flat head but anything else kinda scares the crap outa me
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Unlikely...and definitely not Briggs by the description. Very high probability it's a Tecumseh. Funky pto is difficult to work with.

I just did more than my fair share of Googling- not sure where I got the extra patience. Anyhow, Many Toro mowers and snowblowers were in fact Suzuki-powered. Doesn't change the fact that the OP's got a Tec, but verifies what I'd heard...

(Example- Toro CCR 3000- 5hp Suzuki 2-stroke)
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
Many Toro mowers and snowblowers were in fact Suzuki-powered.
I do not disagree. They are, however, rare. That's why I said "Very high probability it's a Tecumseh.".
I might add that some snowblowers are Briggs built R*Tek engines. Same block as DuraForce powered L-B mowers. Major difference between them is induction system...piston ported vs. reed.
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
Nope, I try to avoid political tv and radio, it's all blabbing to me. It's from the movie Fired Up.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Not to jack the thread, well maybe a bit, for informational purposes. ;)

Today I bought a Toro CCR-3650 2-stroke snowblower, as I've been trying to do for a while. I needed something lightweight for my walkways. I got the old "Ran last year, won't start this year" routine, so I got it cheap. Compression felt good.

Several tugs, nothing. Clean and gap plug. More tugs, smoke. More tugs, and away she goes! Not even sure how old the fuel was, I just wanted to try before draining tank and cleaning carb. Ya gotta like it!

Anyhow, this Toro appears to have one of the above-mentioned R*Tek engines. As Russ mentioned, what I can find online suggests it is very closely related to the Duraforce engines, and yes, the difference does seem to be the induction system- not that I ever doubted you!

A few curious questions-
*Who actually makes these engines, and how are Lawn-Boy, Toro, and the engine manufacturer related?

*I've found indications (but nothing verified) that this could be a 6.5hp engine. Thoughts?

*For now, this snowblower will remain a snowblower. Later, who knows. Aside from shaft adaptations, I'd like your thoughts on kart/bike suitability?

Again, sorry for the jack. I figured it was closely related and may end up with commonly useful info.
 

The Mechtician

Gargamel Jr.
Messages
183
Reaction score
1
Location
Surrey, BC, Canada
I love two strokes, but without a tuned exhaust they're limited in their ability to make power. Even a straight pipe cut off at the correct length will make more power than the shoebox muffler pictured on Russ's engine. If I were to use one of these engines as a prime mover, I'd try to adapt an expansion chamber from a dirtbike of similar displacement. A 125 motocross bike is probably your best bet, you can find used pipes all day long on ebay for cheap, like this one: 96 RM125 Rm 125 Header exhaust pipe 23. With a tuned pipe, you should see large increase in power from even an air cooled piston port machine.
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
Who actually makes these engines
Briggs & Stratton.
...how are Lawn-Boy, Toro, and the engine manufacturer related?
Toro purchased Lawn-Boy from OMC (Outboard Marine Corporation) in 1989 and subsequently contracted B&S to manufacture their snow engines.
B&S snow engines are nothing more than a modified Lawn-Boy mower engine.
Snow engines are piston ported while the mower engine is reed ported.
In short, snow engines are B&S manufactured while Lawn-Boy mower engines are Lawn-Boy manufactured.
I've found indications (but nothing verified) that this could be a 6.5hp engine.
My R*Tek manual indicates 5hp.
thoughts on kart/bike suitability?
Suitability is good, but I was very unhappy with performance.
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
With a tuned pipe, you should see large increase in power from even an air cooled piston port machine.
Not necessarily...and might be a backwards step. One cannot expect a performance increase by just haphazardly throwing on an expansion chamber from something other than it's designed intention.
I've done the math. There is nothing out there that will suit my needs.
For now, I will stick with my megaphones.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
im likin' that tank mount ;)

is it just a weird angle, or is that tank lower than the carb? gravity feed?
 
Status
Not open for further replies.
Top