TAV Compatibility Question

Status
Not open for further replies.

Stratogeezer

New member
Messages
105
Reaction score
1
Location
Norcross, GA
Hi - Can anyone identify this backplate? I believe this TAV backplate is for a Comet 30 series (or 20?).

My question is - If I buy a 40 series clutch (drive wheel) and 40 series driven wheel - can I re-use this backplate with those 2 new components, or is it not compatible? Ignore the driven wheel that's in the picture - it would be replaced.

If this backplate WOULD work, how would I determine the belt size needed?

If this back plate WOULD NOT work - just let me know.

In case it's not obvious - I'm trying to cobble together a 40 series TAV, during a time where they are scarce. I need the big, 1" bore 40 series (or 44) to fit my Briggs 18hp engine that I'm mounting on a kart.

Thanks!
 

Attachments

  • IMG_0552.jpg
    IMG_0552.jpg
    92.8 KB · Views: 4
  • IMG_0553.jpg
    IMG_0553.jpg
    75.9 KB · Views: 5

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
that is a comet tav2 30 series back plate and you may be able to squeeze in a 40 sereis but i dont think you can fit a 44 sereis. also he jack shaft on the back plate may be to small in dia for a 40 series. i have no clue which belt you should use though. good luck :thumbsup:
 

Stratogeezer

New member
Messages
105
Reaction score
1
Location
Norcross, GA
that is a comet tav2 30 series back plate and you may be able to squeeze in a 40 sereis but i dont think you can fit a 44 sereis. also he jack shaft on the back plate may be to small in dia for a 40 series. i have no clue which belt you should use though. good luck :thumbsup:


Actually they said they had a 40 series clutch and a 44 series driven wheel. Would that make it too big for this backplate?

If the Jackshaft that I've got on this 30 series backplate is too small....I might not be on the right track. The sprocket on the Jack shaft is for a 40 chain.

Much appreciate the info!
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
i dont think theres any way of fitting a 44 series driven on this with any type of driver and theand that plate was made for ayssymetrical tcs. 40 and 44 series clutches are symetrical so unfortunatly i dont think that plate well work fow you. i would suggest you set up somthing like the picture below or you can gt a 1" bore 30 series driven and 30 series belt like the third pic. anyway good luck:thumbsup:
 

Attachments

  • BTK_TC_2.JPG
    BTK_TC_2.JPG
    122.2 KB · Views: 9
  • torque_converter_2.jpg
    torque_converter_2.jpg
    24.5 KB · Views: 10
  • 0.jpg
    0.jpg
    14.4 KB · Views: 5

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
The clutch assembly is series 30, series 40 is not compatible with that plate, you'll need to construct your own jack-shaft for the driven clutch. Series 40 drivers are compatible with series 44 driven clutches you will have no problem with that just make sure you have the windings correct for inboard or outboard mounting on the driven. Once you've determined where you want to place that jack-shaft in relation to the motor you can begin to take measurements and we'll cross reference to find what belt you need on the comet sizing chart. The main belts still out there for series 40 are 203783, 785, and 787.
 

Stratogeezer

New member
Messages
105
Reaction score
1
Location
Norcross, GA
The clutch assembly is series 30, series 40 is not compatible with that plate, you'll need to construct your own jack-shaft for the driven clutch. Series 40 drivers are compatible with series 44 driven clutches you will have no problem with that just make sure you have the windings correct for inboard or outboard mounting on the driven. Once you've determined where you want to place that jack-shaft in relation to the motor you can begin to take measurements and we'll cross reference to find what belt you need on the comet sizing chart. The main belts still out there for series 40 are 203783, 785, and 787.

Thanks Blaz - so basically if you use a 40 series - you don't need a back plate - instead you need the jackshaft assembly?

When you say "windings correct" - do you mean install it with the correct side out for the driven wheel?

The place I was talking to had a 40 driver and 44 driven - and I didn't buy them because I thought I still needed a backplate. If not- I think I can handle building the J-shaft assembly. I'm sure there are photos on this site.
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
When I say windings your driven clutch which is the larger one is wound a direction specific to its mounting, you know these clutches expand and contract to change the gear ratios it only makes sense that the driven clutch would be directional right?

I'm simply saying there was never a production plate for series 40/44 and you had to make one from scratch, those black boxes you may see in pictures under the motor that includes 2 bearings for the 3/4" jack-shaft is a part made by ThunderKart which is now out of business.

There should be several set-ups by other users you can view to construct this, any motor over 11hp should be using this assembly. Best of luck and if you have further questions we'll be here.
 

Stratogeezer

New member
Messages
105
Reaction score
1
Location
Norcross, GA
Thanks again

Blaz - thanks again for your guidance - I think I'm going to grab that 40 drive and 44 driven while it's still available - and build the Jack shaft myself. Once I figure out where I'm going to weld the jack shaft assembly - I'm sure I can measure the distance to get the proper belt size.

From that point - I'm guessing it's a matter of choosing the right gear ratio for the J-shaft and axel-mounted sprocket. :thumbsup:
 
Status
Not open for further replies.
Top