Someone's selling a Victa engine :P

Status
Not open for further replies.

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
Just saw this on ebay,

http://www.ebay.com.au/itm/Motor-Go...Go_Kart_Parts_Accessories&hash=item4d00360a7c

Someone wants $125 for a Victa engine... :D
Someone wanted to buy it ..... :D

Need I say more? It's not even tuned or with a clutch adaptor

Going by that, I've probably got over $1k worth of Victas! :arf:

But that one is special, it's an actual horizontal shaft Victa, it may well not need a crank adapter because these generally came with a 5/8" keyed shaft. :D

That's not the only reason it's special, it's a Mk3 125. It's got bigger crank journals than other 125s (20mm vs 17mm) and still has the cast iron con rod which makes for an indestructible bottom end (I've never heard of anyone blowing up a 17mm crank anyway). It's also got the same ignition system and flywheel as an early 160. :)

IMO, that crank in an early 125 (the ones with the bridged ports) would be the ultimate Victa.

I have one of these engines, I got it off a cylinder mower. My guess is they got theirs from the same machine, that throttle is same as the one on my mower. If it is, it'l have a tapered crank.

Interestingly, notice how there's an extra fin at the base of the head? Well there's a 3mm spacer in there to reduce compression. Also, because it's horizontal shaft the G3s governor wont work so there's a special throttle butterfly in there that will only open half way.

I found a brochure ages ago on these engines, it displayed a torque curve, from that I calculated that it produces 2.7hp. Not bad for a something at half throttle and drastically reduced compression. I can't remember the torque figures but they were quite impressive. Max torque was at idle, just like Victas feel. :)

Is that motor worth $125? I'd say it is if it's got the keyed crank, given it looks to be in great condition and has a new ignition system, decompressor and fresh carby, that's as good as they get really. Try find another horizontal shaft engine in that condition for that money.

Thanks

Hayden
 

jman231994

New member
Messages
724
Reaction score
3
Location
Australia
I stand by my claim that you are the Victa God.

I always figured they just had some sort of tapered clutch for the cylinder mowers. But a straight shaft makes more sense. Would the tiltacut edgers have the same engines? I know they have the same orange cowling and the bun muffler......I want one now :worried2:

Darn my victa addiction, So far I have a few powertorques, a few mark 4 160's, an early 160(not sure of the model itself, but off a 67-68 corvette) and really keeping my eyes out for an early 125 to make a nice race engine from hahahahaha

Would the HP output be much more on a standard 160 with a higher compression ratio and a bigger bore?
 

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
I stand by my claim that you are the Victa God.

I always figured they just had some sort of tapered clutch for the cylinder mowers. But a straight shaft makes more sense. Would the tiltacut edgers have the same engines? I know they have the same orange cowling and the bun muffler......I want one now :worried2:

Darn my victa addiction, So far I have a few powertorques, a few mark 4 160's, an early 160(not sure of the model itself, but off a 67-68 corvette) and really keeping my eyes out for an early 125 to make a nice race engine from hahahahaha

Would the HP output be much more on a standard 160 with a higher compression ratio and a bigger bore?

I'm not a god, just a guy who really needs to get a life. :p :eek:

Just to clarify, the cylinder mowers do have a tapered clutch, not keyed. :( No idea about the tiltacuts, they all seem to be vertical shaft though. I've never actually had a play with one, I'd love to pull one apart. :D

The best thing I ever did to cull my collecting of Victas was to stop going to the tip, I only ever went there so I could look at stuff. :roflol: Although, I did find a back way into the tip yesterday.... :eek:

I've got probably half a dozen Power Torques, 2 or 3 125s and I honestly don't know how many 160s, probably half a dozen or more.

The worst part is none of those are attached to anything. :eek: I don't currently have a working/complete lawn mower or go kart or minibike. :eek:

As for making more power out of that combo, certainly a hell of a lot more than 2.7hp! One would expect a 160 free of such limitations to make nearly double that. :D

But more than a standard 160? Well yes it should, but not a lot. Assuming it's bored to 172cc then that's a 7.5% increase in capacity, but then there's what boring does to the porting. Basically because the ports have a bit of an angle on them when you bore it out it makes the porting a bit more tame (and 160 Victas have tame porting to say the least, but that makes them excellent on a kart) so even though you've got 7.5% more capacity you probably don't have much more in the way of power (you'd struggle to feel 7.5% anyway). You could get around that pretty easily by just fitting 2 base gaskets though. :) I never felt shaving the head made any difference, but then it's generally accepted that you can't really feel less than a 10% difference in power, and that's what you'd expect it to be really. Porting it would yield great results but then you'd lose the awesome flat power curve feeling that Victas have.

I really need to get off my arse and finish this minibike so I can start properly playing with Victas again. :eek:

Thanks

Hayden
 

jman231994

New member
Messages
724
Reaction score
3
Location
Australia
Oh god what was I thinking of, it might be the one before the tiltacut, one of these http://www.theflyingbanana.com/Mowers/littlelucifer01.JPG

Your doing better than me in a way, you beat me on engine numbers, since my kart isnt finished, you win.....especially since my kart has been "almost finished" for about 2 years now :| I always end up changing something and then screwing up a weld somewhere so I change it again :worried2:

I havent ported mine out for the kart, I did do it to the corvette engine to see what I could do, cant get the cow back together now cause of a stuck bearing :ack2: My kart motor is 20 thou oversize, which isnt much but it does earn it the name big bore by default :sifone:

My stupid council just decided a few months ago that the reuse centre at our tip is pointless and is now closed to the public...$20 victas, $15 on a good day.......all going to landfill now I suspect, quite sad. Ah well, more incentive for trashpicking.

FINISH YOUR MINIBIKE haha theres some incentive. There needs to be more victa powered things out there for the world to see.......like a smoothie machine, washing machine, blender, pressure hose.......mcflurry mixing spoon. :roflol: hehe
 

sexyvicta

New member
Messages
806
Reaction score
2
O
My stupid council just decided a few months ago that the reuse centre at our tip is pointless and is now closed to the public...$20 victas, $15 on a good day.......all going to landfill now I suspect, quite sad. Ah well, more incentive for trashpicking.

they be sending stuff straight to the scrap dealer i'd say. Way easier
 

jman231994

New member
Messages
724
Reaction score
3
Location
Australia
Gentlemen, guess what I just found on gumtree

http://www.gumtree.com.au/s-ad/went...h-centrifugal-clutch-and-sprocket-/1000104666

Someone will get a great deal on that considering the cost of a centrifugal clutch over here. I think I can see the spacer at the bottom of the cylinder like you were saying too.

And yea, the tips website even says by closing the reuse centre they will be helping the environment.....assuming it ends up getting recycled its good, although all of the beautiful old engines will get turned into paper towel holders and screws and stuff. I wonder what theyll do with the fibreglass stuff and everything.....cant be good for the environment.

The other reuse centre in my area however is a total ripoff, they want $50-100 for mowers that they havent even started up or anything....they are effectively rubbish to people other than us. Expensive computer parts too, considering theyre likely broken :furious2:

EDIT: just made a thread about that engine to try and con a newcomer into buying it so the Victa kart population will rise :D
 
Status
Not open for further replies.
Top