Slightly weird engine...

Status
Not open for further replies.

Krustalien

Battlebot builder!
Messages
109
Reaction score
1
Location
South of Spain.
Just thought it could be interesting...

I have a 7hp two stroke 166cc water pump engine here. It's a lovely piece of kit. RPMs are 4500, 5/8" shaft with nothing but a screw thread. It runs great. Just need to tweak the idle speed and give it an exhaust and a slightly more restricting air filter and it'll make a fine little project motor!

Except of course, the shaft. Any ideas on how to make the shaft usable are very welcome. I have thought about cutting a keyway, and also about putting a piece of metal tubing over the top to make it 3/4", and cutting a keyway into that. Still, any suggestions or tips would be very helpful!

Also, anyone know how I'd go about making an exhaust best suited for this engine? If I am not mistaken, two strokes like back pressure?

Thanks! Here's some pics, sorry for the bad quality.

http://yourimg.in/m/86v949a.jpg
http://yourimg.in/m/hum22z3.jpg
http://yourimg.in/m/b0j96a4.jpg
http://yourimg.in/m/b2ek09y.jpg
http://yourimg.in/m/d18b23t.jpg
http://yourimg.in/m/8p1gb20.jpg
http://yourimg.in/m/1683t39.jpg

If anyone's wondering, it's a "Campeón H-165" also known as virtually unheard of! :roflol:
 

robbie

New member
Messages
857
Reaction score
9
Location
Osceola, Missouri
centrifugal clutches are available with 5/8" shaft. See if one will fit, and if it does, cut a keyway in the shaft and forget about the threads.
 

T-man

New member
Messages
1,232
Reaction score
4
Location
Missoula,MT
This must be the engine you were talking about. That is in good condition. I know you were thinking of a 6.5 also, you might want to think about this. If you use this 7 hp and something goes wrong with it then how easy would it be to find replacement parts ?? It would be much easyer to find parts for the clone 6.5 ... that is a rare engine you might want to scout around for any collectors.
 

Krustalien

Battlebot builder!
Messages
109
Reaction score
1
Location
South of Spain.
Thanks for the replies.

Yes, this is the engine I was talking about. We gave it a good clean (you wouldn't know by looking at it!) and it's looking pretty snazzy now. I have thought about just dropping this and going with a 6.5 but, this engine is useless as it is. If I mess up cutting a keyway, then it's equally useless. I can only benefit from trying to make the shaft usable. As engines go this is a powerhouse if comparing it in weight to a clone, about 30lbs or less.

As for finding parts, not online. This thing is for old farmer-types in Spain, there's very little trace of the machine on the internet. If I wanted to replace the crankshaft I'd have to find this same engine around where I live, which actually shouldn't be too difficult. When I was looking for engines a while ago, someone had a ~5hp version of this thing. The guy wanted 50 dollars or so for it, which would have been fine, if it weren't filled to the brim with mud and old dirt and straw and god knows what else. It didn't even turn, completely jammed. It would have never run, lol. :ack2:

Anyway, yeah I think we may try and cut a keyway. As I said if we mess it up, nothing is lost. I just spoke with my dad and the thought of buying a clone is now in his mind, so we shall see where that leads if anywhere.

Thanks again! Any words on an exhaust for it? :huh:
 

augidog

New member
Messages
329
Reaction score
0
exhaust suggestion...

http://en.wikipedia.org/wiki/Expansion_chamber

search ebay or similar sites for "expansion chamber" and snag something that was made for comparable displacement, then let the fabrication-games begin. you can tune the pipe to your needs by using different lengths of high-temp exhaust tubing which will double as a handy flexible fitting, as chambers usually use spring-fittings to isolate 2-stroke vibration & avoid breakage.

here's a couple very quick examples:

polaris snowmobile 340 for $70

$(KGrHqJ,!lwE6C8-G97lBOq2YWcbHg~~60_12.jpg

kawasaki 200 for $25

$(KGrHqUOKowE5380lRRQBOpeKBl8,Q~~60_12.jpg

etc...

i'm still pondering how to adapt the shaft, without machining it's gonna be tough to get something to grab. however, if you'd consider swapping cranks, then it's no more work to remove the existing and have a shop cut a keyway for you...a good time to look at rings and seals, too, both of which can be bought by size if needed. a "loose" ring-set is not necessarily a bad thing for a 2-stroke, but worn seals can affect case-vacuum & therefore performance.

that engine sure looks like fun, and worth the effort, imo...but that's just me, i love salvaging.
 

Kaptain Krunch

Pro Junk Collector
Messages
4,636
Reaction score
6
Location
vermont
I would just cut the key, i wouldn't trust something like that to propel you. I once welded a sprocket onto a hub for a 5hp go kart, because both were all messed up, at the time i didnt have 220 so i had to use my little mig welder which was not powerful enough, and i actually ended up snapping the welds within 15 minutes of driving.
 
Status
Not open for further replies.
Top