shaft swap

Status
Not open for further replies.

MisterRoboto

New member
Messages
97
Reaction score
0
i am pretty inexperienced with small engines which is probably why i ended up with a short shaft briggs engine that wont fit a clutch... anyway just the other day i got a 5 dollar briggs from a kid that is very beat up but has the longer crankshaft.

long story short... im thinking about taking the great running short shaft briggs apart and trying to slide the long shaft in without taking the piston or valve tappets out if possible.
so anyone think this is at all possible? or have any words of advice or warning?
thanks

 

MisterRoboto

New member
Messages
97
Reaction score
0
thanks guys. im gonna keep watching for others thoughts and probably stop by a small engine guy tomorrow see what he thinks
 

MisterRoboto

New member
Messages
97
Reaction score
0
well i stopped at the small engine guy today and hes a bit of a joke... didnt even come outside just yelled at me through the screen in the window
 

Gokarts4Life-11

The odd one
Messages
260
Reaction score
1
Location
Ontario, Canada
I have one option but it will call for a new clutch, you could get a piece of pipe with a 1" OD, 3/4" ID, 0.120" wall. Then cut it longer than the shaft of the engine. Also you'll need to make 2 key ways, 1 for the clutch and 1 for the engine shaft. The downside to this is that you'll have to buy a 1" clutch and a piece of steel pipe. I did this with a torque converter to increase the diameter and length of my pto shaft. (a few members on this forum showed me this idea, worked great).
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Take the crankcase cover off the other one, and see if they look the same, if so remove it completely and try it.
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
How much usable output shaft length do you have there?
Does it have a keyway and a threaded hole at the end?

I've heard of guys bolting a length of 5/16"ID x 3/4"-OD brass (or steel sleeve) extension to the end of the crank to give your needed length, and then you'd need a Bi-directional clutch installed Inboard so most all the stress would be on the crank itself, with your extension only needing to give minimal support. I'm not sure what brand clutch they were using, but I'd guess the design of some models would make this fairly simple mod more doable.

Another (exspencive) option is I'm pretty sure the Noram Arena Clutch is made to work on short shaft cranks like yours. It comes with a spacer that's only needed when installed on normal/long shaft engines. You can see the spacer here in this pic:

 

MisterRoboto

New member
Messages
97
Reaction score
0
How much usable output shaft length do you have there?
Does it have a keyway and a threaded hole at the end?

I've heard of guys bolting a length of 5/16"ID x 3/4"-OD brass (or steel sleeve) extension to the end of the crank to give your needed length, and then you'd need a Bi-directional clutch installed Inboard so most all the stress would be on the crank itself, with your extension only needing to give minimal support. I'm not sure what brand clutch they were using, but I'd guess the design of some models would make this fairly simple mod more doable.

Another (exspencive) option is I'm pretty sure the Noram Arena Clutch is made to work on short shaft cranks like yours. It comes with a spacer that's only needed when installed on normal/long shaft engines. You can see the spacer here in this pic:


oh boy thanks guys for the suggestions.
i have about 1inch and a quarter or lil less of shaft on the running engine. my brother and i have pondered this and we had come up with a shaft extension idea but the only person i know with a lathe is my mechanic and hes already pretty busy.

we do have a bearing supply place in my town but they only have the right size bushing in oilite i think its called and not in brass or steel. they did say that kind of thing is normally special ordered but i didnt bother to ask how much cause i thought it would be alot. i think ill stop in tomorrow or thurs and see how much it might be to order one with my measurements
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
Yeah an Oilite bushing is what I meant when I said Brass, but I heard the preferred method is to cut the end off another crank and use that for your extension. It'll already have a keyway and the threaded center-hole would probably lower the stress on the bolt.

Is your old clutch designed so it'll slide on Inboard with its drive gear facing towards the engine? It'd be best to have a clutch like this beforehand so you could make absolutely sure this mod wouldnt be putting very much side-loading stress on your extension. You'll also want to find out how much of your key will be in direct contact with the keyways in your crank and the clutches drive hub. I'd think you'd want at least a half inch, preferably more.

With just a 5/16' grade-8 bolt holding that extension on, I wouldnt expect it to do much more than act as a spacer and just be giving a little support for the clutch to ride on. Your original crank would have to be doing most all the serious work here...
 

MisterRoboto

New member
Messages
97
Reaction score
0
ah yea i actually hadnt thought of cutting the other crank off to use as the spacer. i have to get a new clutch anyway... the one that i had was off of another engine but appeared to be a belt drive clutch that someone welded a motorcycle sprocket onto. this clutch i ruined when i didnt know to keep the clutch cover on when starting the engine up. :oops:

i think that if i can find a way to cut the other shaft that would be my best bet if i want to use that engine...

the guy at the bearing store said he didnt think oilite would hold a keyway at all, so idk bout that.

if i can get the other shaft cut would i have to drill out the threads and use a shoulder bolt or try to line the keyways up and bolt it on there with a fully threaded bolt?
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
You could buy a 3/4" jackshaft to cut up if you dont want to use your other shaft, but it wont have a tapped hole in the end.. You could also weld it on and file the weld down.
 
Status
Not open for further replies.
Top