Rupp Scrambler Torque Converter Help!

Status
Not open for further replies.

Briggs8Stratton

New member
Messages
51
Reaction score
1
Location
Northbridge Massachusetts
Hey guys, I just bought an old Rupp Scrambler (I think?) today and I need help with a torque converter system. The bottom line is I don't know where to find one that will fit it. The engine is 3/4 shaft and the driven is 5/8. I need to buy a torque converter system that will fit 100%. Does anyone have any ideas on how I can make this work? I don't want to spend too much. PS am I right...is it a Scrambler?

I know it looks different in the second pic but its just the lighting that does that. its the same bike.
 

Attachments

  • image.jpg
    image.jpg
    70.9 KB · Views: 11
  • photo.JPG
    photo.JPG
    251.3 KB · Views: 11
  • photo 1.JPG
    photo 1.JPG
    57.3 KB · Views: 9
Last edited:

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
I can't give you a direct answer...but I believe you're covered....(just saw those options yesterday posted by Itsid) .....

Go ahead and post up HP....(JIK) ....but someone should post a link for a 30 soon.....
 

Briggs8Stratton

New member
Messages
51
Reaction score
1
Location
Northbridge Massachusetts
What do you mean by covered? Can i put any driver pulley on the engine shaft? What about the distance between the two pulleys, it it different on a Rupp? Will the $85 torque converters on ebay fit? Does it matter if it is symmetrical or asymmetrical? Sorry for all the questions! :huh:
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
What do you mean by covered? Can i put any driver pulley on the engine shaft? What about the distance between the two pulleys, it it different on a Rupp? Will the $85 torque converters on ebay fit? Does it matter if it is symmetrical or asymmetrical? Sorry for all the questions! :huh:

No problem....we're here to answer....but, I'm not your man....I meant I'm pretty sure you can get exactly what you need...but someone else will be along with that information in under 24 hours....
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
The scrambler used a non-comet compatible TC (can't recall make and model)
but you can get NOS or reproduction driver parts here:
http://blackwidowmotorsports.net/bearings_tc___clutch_parts.html

That's the one that'll fit the driven you have...
but the fixed sheave isn't avalaible anymore :(

Since it's cheaper to swap to a series 30 TC clone (driver parts $200 with cover... complete clone ~$120)

I think that's what I would do.. I bet someone's even willing to pay a few dollars for the driven you have ;)

'sid
 

Briggs8Stratton

New member
Messages
51
Reaction score
1
Location
Northbridge Massachusetts
Okay thank you all so much. I found a 30 series TC clone on ebay...it has driven, driver and belt along with other stuff. It is asymmetric though and the rupp was symmetric. is that okay? Also will the distance between the driver and the driven be the same with that new TC. I don't want the belt to be too short. More importantly will the two drive pulleys line up with each other without any problems when I set the engine on the mount...because I know the asymmetrical mounts opposite the way the symmetrical mounts.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
No... The TC needs specific belts for the TC to function correctly. They are also built to handle the strains that it is subjected to.
 

Briggs8Stratton

New member
Messages
51
Reaction score
1
Location
Northbridge Massachusetts
Oh okay, I'm trying to figure out the torque converter system for my rupp scrambler. Its impossible to find the stock system so I'm trying to throw something together that will run with the stock driven pulley.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
well first and foremost:
you need to take ALL parts from the series 30 of course;
and then the belt will match the pulleys for sure, no matter if you previous system was different or not.

But more importantly:
if you bought a TAV kit on ebay, it likely comes with a backplate where the jackshaft sits..
And the belt you'll get will fit THAT mounting position, not (neccessarily) the position if you reuse your current jackshaft (which makes sense considering the drive sprocket and such)
So, install the engine and driver, and measure the Center to Center distance (PTO Shaaft and jackshaft)
compare to this list:
https://www.gokartsupply.com/tcbelts.htm#203594A
and get a matching belt in case the one you have is not the correct length ;)

'sid
 

Briggs8Stratton

New member
Messages
51
Reaction score
1
Location
Northbridge Massachusetts
I have to use the current driven pulley on there (its the stock Rupp driven), so how do I go about this TC system. I also ordered a comet 20 series driver on ebay since it is symmetrical. What shall I do? Thanks for the patience! I am just worried there is no way to make it work.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
okay.. sure... NO!

IIRC the series 20 will not fit the driven you have, not only the width but the angles were different...
so no, no match at all.

money well wasted.

you do NOT have to reuse the pulley you have,
if you think you have to,
then I'm afraid, but ask blackwidow for parts of the driver and belt you need.. anything else will likely fail.

'sid
 
Status
Not open for further replies.
Top