rethinking my drivetrain...

Status
Not open for further replies.

DJEEPER

New member
Messages
205
Reaction score
1
OK...so I have been pretty green to all of this....but I have been doing some thinking.

the purpose for a CVT (TAV style) transmission is for a smaller engine to be able to produce more power with gear reduction.

With my engine (V-twin 18HP)....do I really NEED to run something like this?

I figure a clutch will lock up pretty well with enough power behind it to move my kart on inclines.

I am starting to think about belt wear with my engine. If I run a 30 series tav, i will shred belts like nothing else.

I saw a guy with a clutch setup on a claimed 30hp engine...and his kart hauled a**.
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
OK...so I have been pretty green to all of this....but I have been doing some thinking.

the purpose for a CVT (TAV style) transmission is for a smaller engine to be able to produce more power with gear reduction.
Not quite, the engine will not produce more power (in fact some power is lost to the inefficiency of the belt), but will instead make better use of the available power. As you already mentioned it does this through a variable mechanical advantage.

With my engine (V-twin 18HP)....do I really NEED to run something like this?
This question depends on several factors... Where will you be driving? What driving style do you think you will use? How heavy is the (fully loaded w/ passenger(s)) vehicle? How fast do you want to go? Answer those questions and we can point you in the right direction.

I figure a clutch will lock up pretty well with enough power behind it to move my kart on inclines.
A high quality clutch (setup with a single speed) will lock up and hold your engine, but only if the gear ratio is correct and you don't push it too far. Once again, the questions I asked above will need to be answered to give you solid advice.

I am starting to think about belt wear with my engine. If I run a 30 series tav, i will shred belts like nothing else.
You are 100% correct here, using a comet 30 would be asking for trouble. You would need a comet, 40, 44, or atv/snowmobile CVT to handle the increased torque.

I saw a guy with a clutch setup on a claimed 30hp engine...and his kart hauled a**.

I hope that answered your questions, good luck! :thumbsup:
 

DJEEPER

New member
Messages
205
Reaction score
1
Well, im dont have alot of hills out here...its pretty flat. So I would say geared for packed dirt/grass and small hills (2% grades?)

I have 22" rear tires.

I am 155 lbs, the kart will be around like 300 im sure fully loaded...maybe a smidge more?

I want some good speed 35-40? but i dont want it to be a dog off the line. I think with an 18hp v twin motor it will hold pretty well with a steep gear.

What do you think for gearing?
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
With tires that large, you're going to be punishing the clutch by gearing for 40MPH. I don't think even a quality clutch would tolerate that for long.
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
I would suggest around 8:1 minimum and the removal of your governor. You would likely top out around 35-40mph and still have descent acceleration. Still with that gearing I'm not 100% sure the clutch wouldn't start smoking.

ACVT would be leaps and bounds ahead. With the CVT I'm sure you could spin the tires and still reach 35-40mph, not to mention that the comet 40 is extremely durable and requires almost zero maintenance. You might wish to consult toystory on his previous setup. I belive it was very similar to what you're proposing, but with 11hp and a CVT.

If you do go the route of a standard centrifugal clutch, a Noram 1800 should do the job. To be honest though, spending the $150 or so extra over a $200 centrifugal clutch to get a CVT is easily worth it.
 

DJEEPER

New member
Messages
205
Reaction score
1
So you guys would still push me on a 40 series?

Very Well. I was just trying to avoid doing a jackshaft:ack2:

just a bit of extra work
 

DJEEPER

New member
Messages
205
Reaction score
1
yeah, im aware. Im the kind of person who tries to discover all possible roads and know them first...before settling on one.

I will probably sell the 30 series i have now and put that towards a 40
 

spyder1968

New member
Messages
285
Reaction score
1
Location
New Bedford, MA
your kart sounds pretty similar to mine ( weight, power, tiresize etc) and i have been using a 40 series with no problems ( with the exception of my own stupidity occasionally ! LOL !) i currently am running a 7 to 1 ratio ( 10t and 70t) with 22" tires and it will go anywhere ! if i had it to do over though i would prob get a 40 driver, but with the 44mag driven ( 8.5" instead of the standard 7.5") just for a little more low end power. i do not NEED to go as fast as it is capable of now.
when all is said and done......it will be WELL WORTH the added expense and time/effort to install a 40 series !
 

DJEEPER

New member
Messages
205
Reaction score
1
The 40 series is what I will do then....and I might just do the 44 mag driven, depending on cost.[ Learn from your experience there :) ]

Well, it looks like I need to figure out a jackshaft setup.

any help with pics to help me cheat on my design process? haha
are there any simple/easy (does that even exist now-a-days?) way to do it?
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
There are many simple and easy ways to setup a jack-shaft. The most popular is to weld a plate (~.125") to your frame behind the engine. Then drill slotted holes in the plate and mount at least two pillow block bearings. My personal choice would be to use 2 bolt stamped steel flange bearings, but that's just me. Also, I will add that on a 40 series the driven should be supported with bearings on both sides. The big bearing store should have all the bearings you need, along with sprockets, roller chain, locking collars, keyed shafting, and keys.
 

spyder1968

New member
Messages
285
Reaction score
1
Location
New Bedford, MA
i have purchased a couple converters ( 30 series) from them and have had good luck with them. one did need adjusting though as it engaged quite harshly !
that is a standard sized setup though, i believe. ...not the "magnum" sized driven.
then again.....mine does work well.....and i paid a lot more for mine ! LOL !
 

spyder1968

New member
Messages
285
Reaction score
1
Location
New Bedford, MA
i know i have some pics of my old jack shaft setup ( basically factory setup) somewhere. i will try and find them and post em up. maybe newer set up too.
 

spyder1968

New member
Messages
285
Reaction score
1
Location
New Bedford, MA
Pics

These are the only ones I could find of the original jackshaft setup, for now. If you want, I could take a couple of the new setup = much beefier. But this should give you an idea. Hope this helps!
 

Attachments

  • JS1.jpg
    JS1.jpg
    79.4 KB · Views: 8
  • JS2.jpg
    JS2.jpg
    91 KB · Views: 6
Status
Not open for further replies.
Top