replacing new clutch ....

Status
Not open for further replies.

justbecausegtr

New member
Messages
66
Reaction score
0
Location
USA ARIZONA , PHOENIX
how do you know if u need a new clutch or not...

i was just driving then suddently it turn off...and then i have to push it home , but when i push it , it seems like it wanted to start....i tried to start it..and it seems like it got stuck or as like it slipping ... like it not grabbing anymore to spin the motor to start. and when i push the kart ,,,it seems like the clutch is grabbing and it make noise like it wanted to start..then when i got it home . i put my starter in and tried to start it..but it doesnt spin freely it just stuck...and it hard for my starter to start it ..

anyone know what clutch was this ?



---------- Post added at 09:10 PM ---------- Previous post was at 09:02 PM ----------

ps...when i got it to start...it doesnt idle..it just shut off..and i didnt touch the needle at all... it seems like the clutch is stuck or doesnt move...and it not turning freely like it should do like before..it seems like it stuck

and my clutch seems like the horstman HDC - 5b centrifugal clutch ....anyone wanna confirm for me..i think i need a new one
 

DirtyDamage

New member
Messages
638
Reaction score
0
Location
Westminster Colorado
Is that a race engine, on a race kart? Depending on the engine, the diagnostics may be different, and might be the difference between a rebuild or the need for a brand new clutch...difference of some $$
 

rocketkart

Active member
Messages
1,154
Reaction score
17
Location
florida
sounds like you sherd a key on the flywheel and reason why is your clutch gave out and locked up.
 

justbecausegtr

New member
Messages
66
Reaction score
0
Location
USA ARIZONA , PHOENIX
how do u take off the clutch .......the whole assembly...as i will replace the whole clutch it self....to start fresh of...as my clutch is giving me problem.....on the other thread...so therefore if possible please admin delete the other thread..
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
how do u take off the clutch .......the whole assembly...as i will replace the whole clutch it self....to start fresh of...as my clutch is giving me problem.....on the other thread...so therefore if possible please admin delete the other thread..

Threads merged. At least this way we know what clutch you are talking about
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
Your clutch appears to be a Horstman HDC-5CX model. You'll need a Puller to remove it.

You'll find a shop manual and the correct Puller for sale at the Horstman website: http://www.horstmanclutches.com/

Or... a steering wheel (or 3-jaw type) puller like these pics might work instead:
 

Attachments

  • puller.jpg
    puller.jpg
    28.3 KB · Views: 0
  • 0000053_3-jaw-supercharger-pulley-puller_300.jpg
    0000053_3-jaw-supercharger-pulley-puller_300.jpg
    18.2 KB · Views: 53

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Thanks. Anderkart....I was wanting to suggest that...but being completely ignorant of that clutch, I didn't know if there were set-screws, and I'm reluctant to hand out advice if I'm not pretty certain.
 

justbecausegtr

New member
Messages
66
Reaction score
0
Location
USA ARIZONA , PHOENIX
Anderkart.... i however got a hole of that clutch puller from aneightbor...it not ay clutch puller or steering wheels puller...turn out my mom neightbor use the same clutch as me ..and also have the clutch puller for the specifically for the horstman dry clutch puller...so what should i do now
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
Well, ask your mom's neighbor if you could borrow the puller, or even better..
ask him to remove your clutch.

I bet he'll even be able to help you fixing your clutch.

The only other option I can think of is do as Anderkart already told you,
get the manual and buy the puller to remove and maintain it yourself.
(Horstman clutches are not cheap, so you should be carefull with it)
Don't hit it with a mallet or hammer to remove it,
a decent clutch puller is the ONLY way!

from the pics it looks like the pressure plate is slightly crooked
locking the friction discs...
I can't tell for sure, so check that yourself.
if it is, lightly tap the "higher" side of the pressure plate with the back of a screwdriver,
or a small rubber mallet.
I repeat LIGHTLY!

it should pop out eventually.
if not, remove the springs first and try again.
once it's disengaged, get an airduster or compressor to blow out any dirt from the friction discs as good as you can.
Maybe that's all that needs to be done to get it back into service for now.
BUT: you should start buying maintenance parts (a set of friction discs and floaters and the spanner and puller would be good for example)
The friction discs will come in handy sooner or later, so even if you do not need them now, you will some day.
once it locks up on you again, you can remove and disassemble the clutch yourself with the new tools you got ;)
check what's out of specs with the manual and buy whatever is needed that you do not have yet.

in case you had to remove the springs to free it up, be sure to reinstall them properly (do not forget the washers)

'sid
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Just curious' sid.....does he make any more sense in German....:lolgoku:

It's all good....JBC....at least you aren't asking for dong.....(that's kinda an obscure reference)....but you are a little hard to understand at times....but I couldn't begin to post in Vietnamese....
 

justbecausegtr

New member
Messages
66
Reaction score
0
Location
USA ARIZONA , PHOENIX
well i took the clutch apart..and the only part i haven take out it the main clutch housing where it need the clutch puller to take out..now how come after i disassemble the things and i tried to turn the motor and it still seems like it hard to turn, like it turn freely for a bit then it hard..and once i turn it pass the hard sections , then the crank turn freely again for maybe 3/4 of a whole turn then that 1/4 of a turn to complete the whole turn it hard again
 
Status
Not open for further replies.
Top