Remove fixed faced sheave TC30

Status
Not open for further replies.

Growup

New member
Messages
12
Reaction score
3
Location
Devon UK. TQ11
Hi there, Manco LXT, Comet 30 TC.
The driven pulley was not returning properly so I removed half the driven pulley from the jack shaft, the fixed face sheave does not want to come off. Is it just rusted on by the woodruff key?

Any ideas how I can remove it safely from the jackshaft?
Can the jack shaft be removed if I remove the other nut.
Bit of debris inside, the sheave face is a little warped.
Do the spring and insert buttons look worn?

Your thoughts appreciated.
 

Attachments

  • CRW_0014.4.jpg
    CRW_0014.4.jpg
    495.3 KB · Views: 11
  • CRW_0017.4.jpg
    CRW_0017.4.jpg
    597.4 KB · Views: 11
  • IMG_0022.4.jpg
    IMG_0022.4.jpg
    487.4 KB · Views: 10

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
the spring wasn't preloaded last time that thing was reassembled I assume;
that's why it didn't return properly.
Apart from that single button with a dent, they look okay to me;
if you can carefully pry them out, just swap this one with it's twin.

if the spring is worn or not is impossible to tell from the pic I'm afraid;
I'd say chances are good it's not.

Now, removing the fixed sheave.. it's just stuck..
good penetrating oil, patience and after a few hours/maybe days a light tap or two with a rubber mallet and it'll come off.

'sid
 

Growup

New member
Messages
12
Reaction score
3
Location
Devon UK. TQ11
Thanks Sid, would a bit of heat from a blow torch help or just be patient with the oil.
Its difficult to get a mallet behind the driven pulley.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
sure a blow torch will help; just make sure to not heat up to a point where the grease of the bearing behind will boil out ;)

No need to get behind the sheave, tap it from the side, or from the front;
all you want is to create small cracks in the underlaying rust to help the penetrating oil to actually penetrate ;)
basically the cool version of what your blow torch will do too.
No need to whack the pulley off with a hammer :D (light taps, remember)

Once you have the feeling it should come off (say it starts to wiggle but is still stuck at one point)
screw the nut back on for a few threads (to protect the jackshaft end from mushrooming)
and then hit that (best if you wedged a piece of wood behind the sheave)
Don't get too violent though.. rather add oil and patience than brute force!

You don't want to break the sheave or something else in the process.
As much force as you think is safe, but as little as possible when in doubt.

Oh and the better the penetrating oil, the quicker it goes,
WD40 for example is NOT the right choice for this task.
(at least not the original formula.. I haven't tested their penetrating oils yet)

I use Caramba products (70 or the intensive rust remover for issues like yours)
but that's a german product and it's likely expensive in the UK...

'sid
 

Jrgunn5150

Rudderless
Messages
1,028
Reaction score
12
I have no help to offer, but what size was that nut? I need to buy a socket lol.
 

Growup

New member
Messages
12
Reaction score
3
Location
Devon UK. TQ11
Quick update, I submerged the end of the sheave / jackshaft in Plusgas for 24 hours, I put the Kart on its side. Still would not move so removed the whole jackshaft assembly and supported it through some scaffold and used a lump hammer / wood to push the jackshaft through. It worked.
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
Quick update, I submerged the end of the sheave / jackshaft in Plusgas for 24 hours, I put the Kart on its side. Still would not move so removed the whole jackshaft assembly and supported it through some scaffold and used a lump hammer / wood to push the jackshaft through. It worked.

Awesome!
 
Status
Not open for further replies.
Top