Problems with 6.5hp, low power

Status
Not open for further replies.

Biggie-Diggie

New member
Messages
11
Reaction score
0
Location
Monterrey, Mexico
I'm new in this environment of the karting. Just started with a second hand (junk yard) kart, 6.5 HP, 196cc homelite.

I had troubles with the carburator, so changed it.
The thing is that when it just starts the engine sounds good, when warms up and it is supposed to be ready to go for a ride, if just die.

The spark plug is bran new.
I made a header exhaust, and instaled a hi flow air filter.
Governor is removed.

If the kart is on the jack, (with the tire free to run), the engine move them well, acelerate well, but when it has the tires on the floor (loaded) then at the moment when you step the gas pedal the engine turns off.

Is there something else that I had to check? or, how can I have a better diagnosis of the trouble?

Thanks in advance for your help.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Lets see some pics of the whole kart, throttle and carb linkages...
Did you remove all the pieces of the gov??.
 

Biggie-Diggie

New member
Messages
11
Reaction score
0
Location
Monterrey, Mexico
Thanks...

I removed all the parts of the governor.
Re-did the linkage for the throttle
 

Attachments

  • 20170418_123648.jpg
    20170418_123648.jpg
    268 KB · Views: 23
  • Avatar DIY Kart Forum.jpg
    Avatar DIY Kart Forum.jpg
    320.4 KB · Views: 22
  • 20170418_143426.jpg
    20170418_143426.jpg
    232.4 KB · Views: 27

Kleyny

New member
Messages
140
Reaction score
4
Location
Brisbane Australia
When you fitted the air filter upgrade did you rejet the carb?
If it was mine I would probably change the way your sparkplug lead is as well, way too much of kink in it for my liking.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Well, if you can find another carb you can use that jet, and enlargement that to a better size.
You'll need to get a small number size drill bit set..
Gauge it with a drill bit, then drill the next size up, do a plug reading.. See if performance improves.
 

Flyinhillbilly

The great cornholio
Messages
2,468
Reaction score
132
Location
North West Arkansas
Step 1: remove spark plug and study it closely
Step 2: google spark plug reading chart and study it closely
Step 3: make nessecary carb adjustments
 

karl

Well-known member
Messages
2,449
Reaction score
719
Location
North east Ohio
How well does that pull starter work?
And I thing the rear gas tank mount is in the wrong hole.
 

Kleyny

New member
Messages
140
Reaction score
4
Location
Brisbane Australia
So in the video ( at the end) I'm assuming you are holding the brake on to simulate a load.
Try putting the air filter on and playing with the choke. by putting the choke on say around 1/4 to start off with, this will richen the mixture. Go more or less choke to see where it makes it run better under load. And get back to us.
I always test mine with all accessories on as if I was driving it, no point testing it with the air filter off as you're not going to drive it without one if that makes sense.

Neil
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
260
Location
Ruhrpott [Germany]
GEARING!

from what little I can see on the pics.. you geared in the realms of 4.5 to one or something (that wheel sprocket looks to be very small at least)

And that's not going to haul and adult behind

either that kart came with a TC and you replaced that with a cent clutch
or you though "hey I wanna go at least 40mph" and geared accordingly not realizing
that it's just not possible with the power you have.

'sid
 

Texan

Senor Member
Messages
461
Reaction score
13
Location
Deep In The Heart of Texas
I have a Homelite 196cc engine on a pressure washer. I got it brand new several years ago, but it has always given me problems. Once I get it to run, it will stay running, once I stop it, it is hard to start again. I recently got it running again after it sitting a couple of years, and the same problems showed up again.

Check your fuel shutoff valve, mine was partially clogged and only letting in a small amount of fuel. Once I cleaned it, it ran fine. After like 30 minutes of running, if I shut it off, then try to restart it, the pull start gets real hard to pull. Not sure what that's all about, but now when I use the washer, l just let the engine run constantly until I know I'm done with the job.
 

Biggie-Diggie

New member
Messages
11
Reaction score
0
Location
Monterrey, Mexico
GEARING!

from what little I can see on the pics.. you geared in the realms of 4.5 to one or something (that wheel sprocket looks to be very small at least)
Small sproket 10T - big sproket 62T, the relation is 6.2:1

And that's not going to haul and adult behind

either that kart came with a TC and you replaced that with a cent clutch
or you though "hey I wanna go at least 40mph" and geared accordingly not realizing
that it's just not possible with the power you have.

'sid

Thanks for your coments.
I got this kart with that centrifugal clutch, with the 196cc homelite engine, before of me, this belong to a neighbor, they use this with an adult and one boy, (over 200 pounds).

Yesterday I got another engine, a MPower 5.5 HP, completely original.
The same, started it without load, and sound great, once with the clutch placed, it happened the same, stop working.

today I set apart the clutch and completely cleaned it, disassembly all of it, do some sandpaper work, instaled some grease on the base of the shoes and the outter part of this (where the sproket is) and reinstalled the clutch to the kart.
Well, this time I had the chance to go around the street, not that fast as 40MPH, but good speed; however, if you get to an inclination, you will need more power, or start to push the kart.

Back to the 6.5 HP engine, I'll get the drill bits and open the hole in it, and see what happend.

Thank you all
 

Biggie-Diggie

New member
Messages
11
Reaction score
0
Location
Monterrey, Mexico
Well, I just found the problem, it was the clutch, as it is opened all the time, even with low revs.

Anyhow, I get the jet drilled by a profesional of karting here in Monterrey and it sounds much better, I'm waiting for a new clutch that is coming and then will post a video with the kart running around the block......

Thank you all for your great help!!!!
 
Status
Not open for further replies.
Top