Predator 212 Throttle Linkage

Status
Not open for further replies.

supermanotorious

Winchmaster 5000
Messages
2,088
Reaction score
103
Location
New River, AZ
I'm building a 6.5HP winch for a Florida customer. I de-governed the engine and applied a couple "new" concepts to the throttle linkage. I'm very pleased with the "action".

I took one of the swivel wire nuts from the throttle arm and flipped it upside down so it hangs from the bottom of the throttle control

Cut and bent the governor rod so that it connects the butterfly valve to the swivel nut, had to notch the throttle arm plate for clearance

Took the heavier governor spring and connected the throttle arm to a support bracket under the gas tank

The throttle now accelerates smoothly and snaps back to idle when released!
 

Attachments

  • 024.jpg
    024.jpg
    239.8 KB · Views: 74
  • 021.jpg
    021.jpg
    283.8 KB · Views: 54
  • 022.jpg
    022.jpg
    292 KB · Views: 47
  • 023.jpg
    023.jpg
    171.5 KB · Views: 46

Hellion

Staff Murderator
Messages
9,444
Reaction score
4,372
Sounds like a great 'hack' but the photos are a little hard for me to discern. Maybe I shall endeavor to study them better.

Is it possible to do a video of the throttle moving in and out to better see the action?
 

supermanotorious

Winchmaster 5000
Messages
2,088
Reaction score
103
Location
New River, AZ
I can take better pics and shoot a video in the next few days, search my posts as I've shared other throttle linkage configurations and video to show the action

also, I'd love to find out what tool the factory uses to install the spring clip on the governor sprocket, I have snap ring pliers but can not seem to get them on the clip, could be due to the access, makes me wonder if the governor is one of the first items they install in the block, without the other components in the way
 

Rob711

New member
Messages
64
Reaction score
0
Location
Long Island, N.Y.
Winch? As in powered pulley? Just curious why remove the governor?
This seems like the ideal application for a governed industrial motor.
 

Keystone Motorsports

But who was phone?
Messages
82
Reaction score
1
Location
Lebanon, PA
Ive done similar on mine. Why spend $20-25 on a throttle kit when a needlenose will get the same results?

I dont think those clips are even removable with pliers. I just end up using a screwdriver and a light hammer to mash it off the shaft.
 

Attachments

  • Throttle 1.jpg
    Throttle 1.jpg
    50.7 KB · Views: 62

supermanotorious

Winchmaster 5000
Messages
2,088
Reaction score
103
Location
New River, AZ
that works but some people like a solid connection, I find those clips extremely easy to get off, esp with needlenose pliers- you don't try to "grab" the clip, instead you open the pliers so the tips contact either side of the clip's opening, then you push the clip off the post

you gave me an idea though that combines our methods, instead of notching the lower part of the throttle control, I could more easily drill a new hole for the swivel nut further "back" on the throttle control arm, relocate the swivel nut there
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
I always bend perfect custom coat hanger linkage rods on my 8th or 12th attempt.

That is Funny! I used tips from you on my throttle and bent the Rod on the First try.
"Those who can do... Those who cant teach" :roflol:
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
That is real clean and neat. I love the idea of using the spare swivel lock nut.
This is a great thread. Not wanting to Hi-jack just share the throttle connection options. So here's mine.
One thing I did was I cut off that back section of the throttle plate. It is that part that looks like it says CSI on it. You are resting your fingers on it at 1:00 min in the Video.
It just makes it easier to get the rod in the black plastic butterfly valve.
and I think cutting off the un needed metal cleans up the look a little.

I found a small spring for throttle return. I ran it between the spare swivel nut in its stock location and the screw on top of the cable clamp.
It works great but I was just lucky to have that spring lying around.
and you can see I just stuck the rod through a hole in the stock throttle arm.
 

Attachments

  • IMG_2266.JPG
    IMG_2266.JPG
    136.9 KB · Views: 33
  • IMG_2267.JPG
    IMG_2267.JPG
    120.2 KB · Views: 29

Streetgang

New member
Messages
1
Reaction score
0
Having a similar and not trying to hi-jack, but would like the advice. What is the problem with simply bypassing the governor linkage and installing the coat hanger hack with out removing the internals? FYI- I don't want to bypass the governor, but the throttle doesn't respond by the lever, maybe I'm missing an adjustment somewhere to give the lever more fuel control.
 

Bbqjoe

Banned
Messages
3,455
Reaction score
70
Location
Location, Location
I found it rather simple to pull the internals, pull the arm out, cut the bottom half off, put the top half back where it came from, and put everything else back the way it was.
 
Status
Not open for further replies.
Top