Predator 212 governor removed did nothing??

Status
Not open for further replies.

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
I have the arc air filter adapter, air filter, rejetted carb, and superbox header on my 212.

Last night I removed the governor ( internally ) and got my throttle setup done.

Today i go and test ride it and I don't feel any difference. It doesn't feel like its hitting any higher rpm then before. I know its not going to turn 9k rpm now but I thought I would feel it at least pull to 5k rpm with the governor removed.

My throttle setup pulls the butterfly all the way open. Just wondering what you guys thought about ????????
 

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
I considered that but I thought for sure I've heard of people with stock valve springs and cams reving out to 5k rpm before. maybe not....???
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
What is your gearing, and did you previously hear the motor bouncing off the governor? Do you have a tach or speedo?
 

the-cyborg

New member
Messages
476
Reaction score
6
Location
Spring, Texas
I don't know how you have you're throttle set up, but have you backed out on the throttle stop screw?
This could be acting as a manual governor.
It's always a good idea to post pics when you are having issues, pictures are worth thousands of words.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Without any further detail, I can't help but guess that your current gearing is not allowing the engine to peak. Give up the specs- tire size, gearing, hp, weight, etc.
 

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
Live axle, tav 1 comet 30. Big rear tires on a live axle. I'm sure that doesn't help lol.
I could feel it hitting the governor before, fealt like it was surging back and forth. not sure of the weight and i would have to count the teeth on the sprocket
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Put some ratio rockers in, to give you that little extra power you need?

Once you supply the info, we will be able to help. However, one more question-
If you put the kart on a sturdy stand and throttle up, does it throttle up higher than when you are driving it? If so, it is probably a gearing thing.

If so, I have an idea- maybe try adjusting your driven clutch on the tv so that it shifts later, putting less load on the engine?
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
test the engine with no load. it should rev up higher than stock 3600

EDIT: if it still doesnt rev up then take a video. i think it could be running too rich, but i dont have enough info to call it.
 

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
I adjusted the clutch to the 3rd position and redid the whole throttle setup. It's much faster now but haven't gotten to thoroughly test it.

My current sprocket is 52 teeth on 18 x 9.5 rear tires.
I want to get 16" tires when I replace these and then maybe a smaller jackshaft sprocket to solve the issue.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
that gearing is fine as long as your kart isnt insanely heavy. my bike has about the same gearing with the same TC and it hauls
 

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
It's not extremely heavy. It's a single seater with your average frame with maybe a few extra steel tubes welded on but it has no roll cage and extremely light weight seat cushions so its not a total brute.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
you have a torque converter! DUH. i should have thoght of that before. it keeps a constant load on the engine so you wont be able to rev that high anyways.

EDIT" i think.. someone back me up?
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
No. Once the CVT tops out, RPM will still increase if it is able. You've probably run out of power. For the given ratio, tire size and engine, I don't think it's got any steam left. Gear lower, reduce tire diameter, etc. I had a similar problem with my kart, and actually gained top speed by gearing down.
 

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
Thanks for the advice.
My current budget is in the dumpster but once feb 1st hits I'll be getting all new tires and some spending money to go ahead and fully finish this thing up.

I was going to get the 1.3 rockers, 18lb valve springs, arc long billet rod, and possibly a new carb and probably get the head milled down then hand lap it.

Any thoughts or ideas on that anyone?
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
im pretty sure a long rod will make the piston hit the head

with milling and a flat top piston youre already cutting it close
 
Status
Not open for further replies.
Top