Predator 212 flywheel problem

Status
Not open for further replies.

verdebmxer47

New member
Messages
33
Reaction score
0
Location
Sioux Falls SD
So I just got a new predator 212 for Christmas and looking to upgrade the flywheel.

I was looking on the forums and saw that the PVL flywheel for a clone might work on my motor. I have one on my gx160 So I put that flywheel on the predator and it went on but the measurements of the shaft weren't the exact same as the Honda that it was on earlier but the measurements were super close.

So this is where I'm running into trouble. I was just gonna buy another PVL flywheel but I don't want the flywheel to fail on me because there only meant for clone motors. So now I want to buy an ARC flywheel. the forums say that the tapers between the two shafts are completely different but The clone flywheel fits on my motor

So, that being said, if I order the ARC flywheel for the predator, will the flywheel fit on there correctly or will I have to get a clone flywheel. Some people are saying that some of the predators had the same shaft taper as the clones but I don't know for sure. I would rather be more safe than sorry

I hope this wasn't confusing to read

Let me know what you have to say!
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Id call hat ever place you want to order from and ask About buying a 212 flywheel.... go with that....
Unless otherwise descript.....
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
A predator is not a clone. A "clone" like the lifan/greyhound is just that, a "clone" of a honda... so, the parts fit. Even Genuine Hondas come off the same Chinese assembly line.
The Predator is very similar and many parts fit. but it is not a "clone" due to copyright issues it has to be a tiny bit different. So like Mckutzy said just ask. Parts places want to sell parts but they want happy customers and repeat business.
 

verdebmxer47

New member
Messages
33
Reaction score
0
Location
Sioux Falls SD
landuse, i am removing the govorner so i dont want the flywheel to fly apart. i know its not very common but i dont want to take any chances

---------- Post added at 12:13 PM ---------- Previous post was at 11:57 AM ----------

chancer, i know that a predator is not a clone but the tapered shaft where the flywheel goes is almost the exact same on my predator as it is on my gx160. people are saying that the clone flywheel will not fit on the predator at all but i managed to get it to fit without any modifications to the shaft or the flywheel.

so will the flywheel made just for the predator fit on my predator is what im trying to find out because the tapers are supposed to be different from the clone motors but my predator flywheel is very much the same as my honda clone flywheel.

I know its super confusing to read sorry about that but i cannot explain it on a computer as well as i can in person
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
No I know hear what you are saying the point is it just takes guys like you (or any of us) to "just do it" Hence the term "may" work.
Since the predator is a copy not true clone.
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
If you are not upgrading the valve springs, then I wouldn't worry about the flywheel. The stock springs will cause valve float at about 5000rpm's, saving your conrod from exiting the block as well as the flywheel spinning too fast to self destruct (not that there is any real chance of the flywheel going)
 

joshpepper

New member
Messages
6
Reaction score
0
Location
Fort Worth
The 196cc clone and hemi predator flywheels will interchange in the majority of cases. the non hemi predator will not interchange with clones and hemi preds.
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
ok guys, here is what you do:
1) go to www.arcracing.com

browse their flywheels, look in the product description, and they have all the information you need to make sure the specific flywheel or whatever other part you are getting will fit.

IIRC there are THREE versions of the predator, gen 1, hemi, and gen 3 -im not going to explain which part fits what, because that information is readily available in the product description.

enough said.
 
Status
Not open for further replies.
Top