Predator 212 flywheel destruction

Status
Not open for further replies.

thisismyusername

Donut Eater
Messages
250
Reaction score
3
Ok so heres what happened. My friend did a wheelie on the mini bike, he flipped over the back and the bike fell on its side of the pull starter, which dented in, and the flywheel hit it where it dented it and demolished its self. I have it taken off now, and i was thinking about getting one of those nice flywheels that are meant for higher rpms when removing the governor, but they are 100 bucks. Is it worth it to remove the governor and buy one of those flywheels, how much top end speed would be added on really? My gear ratio is 6:1. Also thinking that if i go that rode what are they chances the engine blows up, like how would i blow up the engine without the governor in but with the flywheel, and what other percausions would i need to take, etc. Thanks for any info i can get if anyone else has taken out the governor and replaced the flywheel before, is there anything else needed?
 

thisismyusername

Donut Eater
Messages
250
Reaction score
3
Heres pics of the damage
 

Attachments

  • 20150919_202546[1].jpg
    20150919_202546[1].jpg
    124.5 KB · Views: 26
  • 20150920_214028[1].jpg
    20150920_214028[1].jpg
    185.5 KB · Views: 34

machinist@large

Active member
Messages
2,865
Reaction score
34
Location
West Michigan, 49331
All your friend wiped out was the plastic fan assembly and the fan housing. Replace those and you're back in business. The main fan backer is in one piece, which has me guessing that the actual flywheel was untouched.
 

thisismyusername

Donut Eater
Messages
250
Reaction score
3
All your friend wiped out was the plastic fan assembly and the fan housing. Replace those and you're back in business. The main fan backer is in one piece, which has me guessing that the actual flywheel was untouched.

Ah yup i see now, where can i get one of these little fan thingy majigers lol.
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
eBay, or calling harbor freight. Look in the user manual at harbor freight "predator 212cc parts manual" parts diagram
 

minibiker

New member
Messages
148
Reaction score
1
Location
USA
**** just run it as it is I cut off every other fin off all my flywheel fans and they never over heat. These motors were meant to be stationary ( not move) so the fan is there to keep it cool when it is just sitting there . As long as your moving it wont over heat . The billet flywheel will help it rev up a little faster because its lighter. But the best thing about it is that you can build it into a race motor and rev as many rpms as you want to get some real power.
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
**** just run it as it is I cut off every other fin off all my flywheel fans and they never over heat.

You should know by now which words are on the "banned" list, please don't use them...

But the best thing about it is that you can build it into a race motor and rev as many rpms as you want to get some real power.

Let me just clarify that by "build it into a race motor" he means adding other high performance parts, such as a billet conrod...
 

minibiker

New member
Messages
148
Reaction score
1
Location
USA
Sorry I didn't think that was a banworthy word its from the bible. Yes a connecting rod is also needed for higher rpms to make a race motor. The billet flywheel is usually the most expensive part .
 

JMINDY

Member
Messages
254
Reaction score
5
Location
Indianapolis, IN
Is it a predator 212 engine? Anyone know if there is a difference in the original plastic fans on a hemi vs non hemi predator engine? I have 2 plastic fans from a non hemi predator engine... PM me your address and you can have one...
 

thisismyusername

Donut Eater
Messages
250
Reaction score
3
Is it a predator 212 engine? Anyone know if there is a difference in the original plastic fans on a hemi vs non hemi predator engine? I have 2 plastic fans from a non hemi predator engine... PM me your address and you can have one...

I got one from my friends predator that he isn't using, and put it all back together and it won't start. :ack2:

It's not turning over at all so I'm assuming it has some thing to do with the kill switch, seems like it's always engaged and wont let the engine start. Yes I plugged in the cords, any ideas?
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
A piece of flying shrapnel may have moved or damaged the coil; disconnect the low oil sensor & kill switch, then verify you have spark...

Sorry I didn't think that was a banworthy word its from the bible.

True but, how often is it used as a mild profanity? ;)

Remember, we have members as young as 13 here, we don't want to teach them any bad habits...
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Sorry I didn't think that was a banworthy word its from the bible. Yes a connecting rod is also needed for higher rpms to make a race motor. The billet flywheel is usually the most expensive part .

Yeah....I only recently released they mentioned the Poboy in the bible.....something about the "jawbone of an ***"...??....I figure that probably refers to my posts.....
 
Status
Not open for further replies.
Top