OLD 5hp Briggs Help

Status
Not open for further replies.

j.concepcion54321

Rebuilding KTM, Need Kart
Messages
1,251
Reaction score
5
Location
East Providence RI
Hey guys, a friend of mine gave me an old tiller engine. Its a 5hp briggs and stratton in pretty rough shape. I think it has some potential though. some of the problems are...

Seized Carb

No Spark

Jerry rigged spark system, ill explain further down.

the tank is all rusted and according to his dad it wasnt venting properly so i guess the tank is broken. lol

and its pretty ugly.

But it was free :wai: so im gonna try to make it a racing engine and if it doesnt work or it all blows up in my face its ok. :roflol:

Ok now to adress the issues...

...the first one is the seized carb. because the carb and tank are attached and the tank is bad aswell im planning to just throw the whole assembly out and order this. http://www.ebay.com/itm/Chinese-Car...s=63&clkid=5560928237762508978#ht_2170wt_1270 then use another tank mounted somewhere else that i already have.

the second problem is the no spark/ rigged system. I tried cleaning up the spark plug and adjusting the gap of the plug a little to see if it did any thing but no luck. Im planning on getting a new plug as soon as the weather clears up and trying again. when i say rigged system is that my guess is the plug boot went out so they cut it and went to go strip the wire and wrap it around the plug. looks like they cut it too short :mad2: so they used another wire in between as well. i mean that the original wire coming from the coil is connected to another wire, and that wire just goes to the spark plug. ***** Can someone tell me if this system will work like that? If so then ill just clean up the wires some and tape em up and leave it like that. will i have any problems by doing this?*****

last problem is the ugliness. Since im going to be taking apart the engine anyways after i know it runs to remove the governor i figured that while i had it all apart id just grind off all the grime and rust off the actual block and all the engine components that may be dirty and then hit it with some paint, let it dry, and put ut all back together. then itd be nice and pretty again.

also it didnt come with an exhaust ( i think, cant check now but i dont remember seeing one ) so im probably gonna make some sort of homemade performance pipe that is quiet but not restrictive at the same time so that it gets good performance and the neighbors and my parents dont kill me.

so what do you guys think of my plan? Good , bad, questions, concerns, etc. feel free to comment.

EDIT: i forgot to mention that theres an unknown problem. When i go to crank the engine i pull the rope and it catches and turns it over, then i go to pull it again and it doesnt catch and it continues to not catch until i spin the shaft manually and then i pull it again and itll catch. and then the same thing happens after that and so on and so forth. How can i fix this problem? I an in too deep with this engine and it is just scrap? or does it have potential to be a nice fast kart engine like im hoping.

Thanks guys for taking the time to read my post. Im done now. :roflol:
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
you probably have the recoil type that has ball bearings. take it apart and clean it out good. dont grind off the paint, wash all the parts and use paint stripper if youre going to strip the block.

ive freshened up a bunch of engines and i think the best thing to do (if there is no internal problems) is strip it down to the SHORTBLOCK and wipe/scrub off all the grime. rebuild carb, wire wheel all the shrouds and repaint them.

looks good, keeping the old paint on the block but brand new shrouds. i actually think its better to do that because painting the entire engine can make it look like a blended together piece of metal.
 

j.concepcion54321

Rebuilding KTM, Need Kart
Messages
1,251
Reaction score
5
Location
East Providence RI
yeah i know what you mean. i wouldnt paint it all the same color anyways id probably do like black engine red cover or white cover. idk. but yeah

anything on the spark? is that system fine the way it is. oh and will that carb posted above just bolt right on and work good?

Thanks
 

Jake.B

New member
Messages
495
Reaction score
0
Location
California-USA
With your spark plug setup. what if you got a new wire that is in between the original wire and plug soldered it on then put shrink tubing on it. i don't see why there would be a problem with it as long as a current is hitting your plug. Is the carb that is on it bowled or does it go directly in to the tank? if it does i wouldn't go with a bowled carb. I'm only saying because i have a fie horse Briggs off a tiller and it is not bowled.
 

j.concepcion54321

Rebuilding KTM, Need Kart
Messages
1,251
Reaction score
5
Location
East Providence RI
Yeah I figured that I would just do that for the sparlk system after I can verify that it works

As for the carb I don't see why the bowled verses nonbowled would make any differendece
 

j.concepcion54321

Rebuilding KTM, Need Kart
Messages
1,251
Reaction score
5
Location
East Providence RI
Ok yeah cause whenever I see the racing engines with slide carbs that's what they look like.

Ok guys well I'm gonna start taking it apart when It gets warmer out and start Trying to fix the problems one by one. Hopefully in the end ill get a good engine out of it.
 
Status
Not open for further replies.
Top