Newbie question on gx390 engine

Status
Not open for further replies.

Dean B

New member
Messages
17
Reaction score
0
Location
German queens England
Hi there guys, I no this will be a stupid question for use but I fire away with it.

I have a old manco 2 seater kart with 5hp Briggs engine fitted.
I can buy a Honda gx390 engine for £100 but was wondering if it has same mount holes so it just bolts straight into my kart?

If the Honda gx390 engine don't bolt straight in with no messing do I have to make engine mounts or can you buy them.
 

Attachments

  • image.jpg
    image.jpg
    439.5 KB · Views: 9

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
:welcome2: to the forum!!!!!! Might as well get this out of the way....(since you never got around to that intro thread) ....

Are you in England? (Since you haven't gotten around to that profile yet either...:lolgoku:)

I can't help you on this question...but someone will be along shortly....

And there are no stupid questions ....
 

crazykart

Crazy member
Messages
1,167
Reaction score
7
Location
Swartz Creek, Michigan
No it won't bolt right up, gx390 is what 11-12hp iirc? Which would mean it would fall under the "big block" umbrella iirc. You'll need to buy a new mounting plate, cut the old off, and weld the new on. On top of that, the 5hp engine you have should have a 3/4" shaft, the gx390 will have a 1" shaft. That means you'll need a new clutch, which iirc run about $100 for a CC that will handle all that. You could go with a TC instead, but that's even more $ (£).

On top of that the engine will be much larger. I have the same kart, and just fit a 212 cc (6.5hp) predator engine on it, and had to slightly bend the seat forward for it to fit. You would probably have to cut and rewelded the seat mounts forward an inch or two, and bend the seat forward a few inches.

If you can get a gx390 for 100£ I'd say get it just to have it, or even resell and possibly double your money. Yes you could make it work, but it will be some work, and cost some money to do...
 

Dean B

New member
Messages
17
Reaction score
0
Location
German queens England
Poboy kartman I will sort my profile out later buddy, and crazy kart I know that I would need 1" bore clutch, was thinking on just buying centrifugal clutch for it, and like you said I might aswell buy the engine to just put aside for anything else that pops up.
Thanks for the info buddy take care guys
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Well there's going to be a bit of a problem, the crankshaft is a tapered shaft. Mounting a clutch is going to be a big problem.
 

Dean B

New member
Messages
17
Reaction score
0
Location
German queens England
No it's not tapered shaft look at picture there above, click on it and zoom in.

Going to go buy the engine for £100 and just make my mind up with what I'm going to do with it when I get it, even if engine don't get used or put onto anything for few months it's still worth buying.

Will be buying a centrifugal clutch for it as seems easiest and simplist thing to do.

Thanks for replys guys take care.
 

XXXStevemanXXX

New member
Messages
60
Reaction score
5
Location
Astoria, Oregon
Dude, it looks tapered in the picture. Ive opened the pic and zooming in makes it look even more tapered, unless you have some sort of cone shaped washer on the thing or the picture is just bad...
 
Status
Not open for further replies.
Top