New guy with some Q'

Status
Not open for further replies.

jeckel7234

New member
Messages
25
Reaction score
0
yes i believe so because there is a smaller amount or surface area for the chain on the centrifugal clutch than the sprocket it causes the sprocket to turn faster. And depending on that relationship decides the ratio and the acceleration/top speed trade off
 

jeckel7234

New member
Messages
25
Reaction score
0
yea were on the same page, and again thank you for the info. ive started drawing it up and gonna start fab later this week
 

jeckel7234

New member
Messages
25
Reaction score
0
i will, im planning on using 1 1/4" square tubing for most of the frame and roll cage if i do it, but what size sheet do most people use for the floor
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
i will, im planning on using 1 1/4" square tubing for most of the frame and roll cage if i do it, but what size sheet do most people use for the floor

Although SHS (square tube) is easier to work with, round tube looks better for the roll cage, but it's up to you.

Floor sheet depends on you but you shouldn't need more than 14 - 16 guage. On my daughters kart I used 0.55mm for the belly pan, but it has a plywood floor mounted to the top surface of the frame.
 

jeckel7234

New member
Messages
25
Reaction score
0
yea ive considered it but i dont have a bender or a decent way to notch all the tubing so i figyure for my first cart ill be better off with square tubing
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
I know I am coming in late here, but if your reduction unit does have a clutch, then it will be the best thing to use. They are practically indestructable. I have just sold one, and here are some pics. Mine was a 2:1 reduction.
 

Attachments

  • 19052012934.jpg
    19052012934.jpg
    140.5 KB · Views: 1
  • 19052012935.jpg
    19052012935.jpg
    128.6 KB · Views: 2
  • 19052012937.jpg
    19052012937.jpg
    95.1 KB · Views: 1
  • 19052012938.jpg
    19052012938.jpg
    87.8 KB · Views: 1

jeckel7234

New member
Messages
25
Reaction score
0
im looking at what size to for with the sprocket and clutch, Northerns website says its max RPM is 3600, so with the gear reduction at 6:1 its really at 600 RPM correct even though the website giving those specs were off of the motor with the gear reduction box
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Then yes, you would have 600 RPM coming out of the redux box. Since most kart setups are happy around 6:1, you would go at 1:1 from there to your axle. Pick a good size axle sprocket that will get you some decent chain/tooth engagement (say 30 teeth), and use a similar sized sprocket for the redux output. You can add or subtract teeth from either sprocket to fine-tune the ratio as needed.
 

jeckel7234

New member
Messages
25
Reaction score
0
the smallest sprocket i could find as a 40 tooth and using the speed calc on this forum it seems like im going to be hard pressed to get faster then 8mph, even with that plugging in a 30 tooth bumped it up to 13mph which still wont do i was still wating to get around 30 mph and i can govern it down from there. Any suggestions on how to get that speed with this motor
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
You are probably best off getting a pilot bore sprocket and getting it bored and keyed by a machine shop. They come in a range of sizes.
Or you could get a weld on sprocket and hub.
Another option is a 'taper lock' sprocket and hub.

Check here for wheels.

Edit: Screw that. Found some sprockets already keyed for a range of bore sizes here
https://www.surpluscenter.com/item.asp?item=1-2123-11-UA&catname=powerTrans
https://www.surpluscenter.com/item.asp?item=1-2123-11-UA&catname=powerTrans
https://www.surpluscenter.com/item.asp?item=1-2123-11-UA&catname=powerTrans
 

jeckel7234

New member
Messages
25
Reaction score
0
what exactly are you referring to about the bore and how will a sprocket keyed for different bore sizes be a benefit? Thanks
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
what exactly are you referring to about the bore and how will a sprocket keyed for different bore sizes be a benefit? Thanks

If you look at the second pic of the reduction unit that I posted, you will see that the shaft is keyed (has a slot in it). For you to put a sprocket on it, you are going to either have to do one of two things:

1. Get a keyed hub that you can bolt a sprocket to. Your sprocket will be a normal plate sprocket. Your hub will have the same hole (bore) size as your shaft, and be keyed (have a slot cut in it). You will then use a key with a setscrew or two to attach the hub to your shaft.

2. Use R_chez suggestion and get a pilot bore sprocket. They usually come with a standard bore size and no keyway. To get it to fit your shaft, you will have to have the bore made bigger and have a keyway cut in it. Going with this sprocket means that you won't need a hub.

Here is a pic or two of what r_chez is talking about. They are off the jackshaft of my minibike, but the concept is the same. I had to have these sprockets rebored and keyed
 

Attachments

  • 23072011529.jpg
    23072011529.jpg
    105.5 KB · Views: 1
  • 23072011528.jpg
    23072011528.jpg
    100.6 KB · Views: 2
Status
Not open for further replies.
Top