new guy needs help

Status
Not open for further replies.

slideways

New member
Messages
575
Reaction score
6
Take all that emissions garbage off of your clone and add a curved header with a muffler. One size bigger on jet with an air filter setup should make it scoot alot better.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
If you haven't got any new wheels yet, I recommend picking up sole ride on lawnmower wheels, about 12", of eBay.
 

eastereggsrus

New member
Messages
22
Reaction score
0
Ihave some lawnmower tires but I'm trying to figure out how to get them to work on my setup, I have a gx140 parts motor so I was going to taked out the emulsions tube and put it in and drill out the main jet, wat size drill bit should I get all the sites I've read say #36 or close but I can't seem to find any #s on them just mm and I now its not 36mm that's big wat size in mm should I use? I have a exhaust welded up now and a modified k&n breather filter, wat other easy and cheap or free mods can I do?
 

eastereggsrus

New member
Messages
22
Reaction score
0
And also I heard if u bolt a 160 head it will raise compression can I bolt on the 140 head? And how exaclty do I advance timing? I now I have to shave the timing key or something like that but not really sure wat that is is there a write up or something? Thanks I love this site I wish all forums were like this
 

slideways

New member
Messages
575
Reaction score
6
I have never seen the emissions setup in person but take it off.. it will probably rob some performance. Drill the jet to .106 which is a #36 bit. You need to get a set of number drills to fine tune the jet sizes. You can't bolt the 140 head on to gain performance but the 160 head is an 18cc head which will boost compression. Many other guys find it better to use the stock head and mill and port it. For what you are doing as a basic build the best bang for the buck is going to be a good exhaust, intake, jet resize and governor removal. Next step would be a better cam, rockers and valve springs. Billet Rod and Flywheel along the way somewhere and then a bigger carb.

You will see the best gain from about a 4 degree advance on the flywheel only after you do the other mods. And i'm assuming you have the governor pulled because the flywheel advance is to take advantage of higher revs.
 

GreyhoundOfYerfDogs

New member
Messages
56
Reaction score
2
Location
Los Angeles
I like your ah-oooh-gah horn.

The rear tires you have look pretty good. With that diameter, you should ideally have a taller gear ratio. Since your axle sprocket is already pretty big, you might run a jackshaft. Run your 12-tooth clutch to say a 15-18-tooth sprocket on the jackshaft, and a 12 tooth sprocket running to your 60 tooth axle sprocket.

Google yerf dog jackshaft for a nifty setup that will bolt between your engine and frame with perfect alignment. Look at agsupply for a variety of sprockets and chain. You might be able to stay close to your $50 budget less clutch, but your next clutch won't burn up.

When you get more money in the future, this setup will lay the groundwork for a torque converter. Then you'll need a live axle. (It looks like a sprocket driving one wheel now.)

You'll need to start by figuring out what chain you're working with. See the chart here and measure your pitch. http://en.wikipedia.org/wiki/Roller_chain
 

eastereggsrus

New member
Messages
22
Reaction score
0
Well I figured out me hole clutch problem, there's like gears that hold the hole clutch on so it spins with the engine, well the gears broke lol, I just welded it on and it works great, I have a maxtorque clutch already on it, I was gona go buy a bicycle speedometer and hook it to the rpms so I don't over rev before I take off the gov. I'm still tryin to find a write up how to do the timing advance I can't figure it out, I m going to buy the speedometer today and hook it up and while I have access the the flywheel I was gona try for the spark advance
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
i don't think a bike computer will be able to read # in the thousands, you could change it so that it says 35 for 3,500 rpm. i would suggest you just get a tachometer.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
i think you should be able to tell if your pushing the engine too hard...

with all those mods a billet rod and flywheel is your next step.
 

eastereggsrus

New member
Messages
22
Reaction score
0
Ok I. Installed the gx140 emulsion tube and drilled out the jet one size bigger, it was a little hard to start and after I checked the spark plug and it was pitch black so I think I got it to big
 

slideways

New member
Messages
575
Reaction score
6
What size did you go to? Did you put the intake and exhaust on yet? If not that's your problem.
 

eastereggsrus

New member
Messages
22
Reaction score
0
Yeah I put the intake and exhaust on already I just started checking witch drill bit would slid in tightly and went up on size and drilled it so its not that big I looked threw it and compared it to stock and I could barly tell so I don't now maybe I didn't have it set right, I put the stock one in so I'm gona run it and see wat color the plug is tomorow maybe my motor is always rich, could it be the emulsion tube? Also I'm running 91 octane gas willl that make a difference?
 

slideways

New member
Messages
575
Reaction score
6
I seem to remember the 140 tube causing a more rich condition so that could be it. You're wasting your money on 91 octane. These motors are made to run the cheap stuff specifically.
 

eastereggsrus

New member
Messages
22
Reaction score
0
I figured it out I left the stock plastic part on the aur filter and set up a airfilter on that I just took off tthe plastic part and made an airfilter adapter and it wrks great now
 
Status
Not open for further replies.
Top