Need some quick help with max torque clutch issue.. Urgent...

Status
Not open for further replies.

e85

New member
Messages
150
Reaction score
1
Location
The great NW
So I bought a predator engine and max torque clutch for a doodlebug. The project needs to be finished tonight so we can take it to the beach tomorrow. Im used to hilliard clutches and noticed max torque uses shaft keys and set screws. I am going to be installing the clutch with the teeth facing inwards towards the engine and my questions are. 1- Do you have to use set screws? And more importantly my second question is. Do I have to trim the keys or something? my predator motor came with a key that runs almost the whole length of the shaft. About half of the clutch will accept the key before there is no more slot left. So do I just trim the key and put it on? do I need set screws since im using a bolt and washer at the end of the shaft
 

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
cut the key to about half inch, grind the edges to make it all even. then slide it on with the clutch and make sure the bushing is lubed. the set screws are nice to keep the clutch tightened where you want it on the shaft so your chain doesn't fall off. a bolt on the end of the clank shaft with a washer bolted on with an air ratchet or impact drill to hold the clutch on is also needed to make sure your clutch doesn't fall of the bike. if you screw it in by hand the bolt will vibrate off the crankshaft.
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Sorry dude but, I'm gonna correct most of that...

cut the key to about half inch,

Measure how much the clutch will take then cut it. If the clutch will take 1 1/2" then 1/2" won't be enough

the set screws are nice to keep the clutch tightened where you want it on the shaft so your chain doesn't fall off. a bolt on the end of the clank shaft with a washer bolted on with an air ratchet or impact drill to hold the clutch on is also needed to make sure your clutch doesn't fall of the bike. if you screw it in by hand the bolt will vibrate off the crankshaft.

A bolt in the end of the shaft stops the clutch falling off but the set screws stop it from wandering back & forth on the shaft.

If you use an inpact gun you risk damaging the bolt &/or the shaft. If you must use an impact gun, use a low setting. A safer alternative is blue thread locker
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Impact gun works well for me. Sure you do risk damaging something, but you also risk damaging the shaft when the clutch falls off because the bolt comes loose. Been there, done that :oops:
 

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
I have had the bolt come off the crank shaft with just thread locker. The impact keeps it on tight just dont go over board and snap the bolt. Half inch is about what you need when you mount the clutch with the sprocket facing the motor on a max torque clutch.
 

sexyvicta

New member
Messages
806
Reaction score
2
impact gun wont damage the bolt, the thread or the shaft unless you're a gorrilla or its set to some crazy high torque setting
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
impact gun wont damage the bolt, the thread or the shaft unless you're a gorrilla or its set to some crazy high torque setting

Yeah- problem is, most people are gorrillas when handed an impact gun.

Regarding the key- You sure there isn't one already built-in to the clutch? They often are, and if there is, you don't need to add anything.

I realize my comments are "too late", but felt the need to point it out anyhow.
 

e85

New member
Messages
150
Reaction score
1
Location
The great NW
bought the clutch from a old mower shop. Clutch was new but packaging looked really old! its one of the max torque clutchs with the black shoe cover not silver. It engages SUPER SMOOTH, but cannot grip as quickly or as hard as my hilliard which sounds like it has engine knock while engaging lol. Hilliard grips a little quicker and harder than the max torque. But the max torge engages like butter compared to the hilliard. And yes, this max torque most deff needed a keey which I had to cut. Must be an older model. I still cannot believe what a difference a bone stock predator made on that doodle bug. Good grief, already enough speed and power that I would want to mod it unless it goes on a kart
 
Status
Not open for further replies.
Top