Need A KeyWay HELP!

Status
Not open for further replies.

SheffieldShedKarts

New member
Messages
2
Reaction score
0
Location
Sheffield,South Yorkshire, United Kingdom
I have a Honda GX and im preparing to put it on my kart but i dont have a Key Way and I have no idea what dimensions I need how should I measure or where can I find the details. I am 15 and new to home construction so :huh: any help is greatly respected.I desperately need a key way or i cant fit my clutch.:mad2: Thanks i hope to be rolling :auto: soon :D
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
your engine shaft doesnt have a keyway in it? you need to get the correct crankshaft (off ebay is your best bet) or a correct engine.

getting a new crankshaft thats keyed, would require you taking apart most of the engine... so if you think youre going to mess it up, watch alot of youtube videos first!

another option is bring the crankshaft to a machine shop and see how much it would cost for them to machine it down and mill a keyway in it. MAY BE $300 or more... beware.

welcome to the forums!
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
I have no idea what dimensions I need how should I measure or where can I find the details.

The keyway for a GX160/200 needs to be 3/16" wide, and 3/32' deep to fit the clutches sold in the USA.

If your output shaft tapers down smaller at the end, you'll need to make sure the inner portion has around a 2" length of non-tapered/3/4" shaft diameter to mount most standard centrifugal clutches. But If your serious about doing this mod, I'd suggest you purchase your clutch and key beforehand, so you'll have them to take the exact needed measurements and be able to test-fit the clutch as your machining the crank.

If the very end of your output shaft does not have a threaded hole, you'll simply need to buy a clutch model that's equipped with set screws to hold it on to the output shaft.
These clutches come with set-screws--> http://www.mfgsupply.com/GoMiniClutchCentMax.html
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
first off... WHAT ARE WE ALL YELLING ABOUT!? sorry, i had too! :D, normal font will suffice :thumbsup:

back on topic of your question. the first thing we must know is what your crankshaft looks like right now.

Please answer all of the following:

- is it tapered? threaded? stepped? something else? (pictures could help)
- what is(are) the diameter(s) of the crank shaft (if there are multiple diameters please list all of them in order from the engine to the end of the PTO)
- how long is the crank shaft?
- what size clutch do you have (a link would be good...)

once again pictures can help.

with that information we should be able to tell you what needs to be done to fit your clutch on your engine and/or give you some simpler solutions.
 

SheffieldShedKarts

New member
Messages
2
Reaction score
0
Location
Sheffield,South Yorkshire, United Kingdom
My crank shaft is threaded inside so i can fit a bolt but the main problem is the grove on the outer of the shaft i need the rectangular rod that fits in there i know how to fit my clutch now just not the sise of the rectangular rod i have spent most of today searching for solutions for this problem i have found a chart (http://www.transeals.com.au/catalogues/files/Transeals_Keyway chart.pdf) but i don't know how i link this with the crank sises.
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
So you need key stock? Try some punctuation. It helps us to tell where one though stops and another begins so they don't all mash together into a blob.

1) So you have a motor, and the shaft is the same diameter the entire length and there is a little groove (a keyway) cut into it?

2) You have a clutch that fits over this motor's shaft snugly?

3) What you don't have is the piece of key stock that fills the key ways and locks the two together so they spin as one?

4) You can probably get key stock at any hardware store.

This is all depending upon whether or not I correctly understood your alphabet soup.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
What gx model? If it has a 1" shaft then the rod will be 1/4" x1/4"
If the motor has a 3/4" shaft the rod will be 3/16"x 3/16"
Hope that helps,
Rob
 
Status
Not open for further replies.
Top