My clutch is burning

Status
Not open for further replies.

shuakarter

New member
Messages
2
Reaction score
0
We have installed a centrifical clutch with sprocket on a go kart and have a 60 tooth sprocket on the axle and a 17 tooth sprocket on the clutch. It is burning bad on take off. Any suggestions:2guns:
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
Can you give us some pictures?

Is this 1/2" pitch or 3/8" pitch?

What size tires are you running?

Just by reading this if I were a betting man I'd take a wild guess you have a Yerf-Dog kart which had a 6.5hp Tecumseh stock which had a 3/4" stock. You didn't think it was fast enough so you put a larger engine 8-13 hp on the kart which resulted in a 1" bore shaft so you could no longer use the 3/4" clutches. Since Comet is out of business you went to buy a 1" centrifugal clutch because you saw the prices on the large torque converters and were turned off, sadly Comet was also the company who made the only 1" bore centrifugal clutch which was also stepped down to 10t, all the other companies Hillard, and Noram who make 1" centrifugal clutches run the shaft of the motor through the whole clutch.This all means you're forced to have a huge tooth count throwing the gear ratio even more out of whack than your 18-20" tall rear tires happen to do. This may be a lot to swallow but I've heard this story before, if I'm wrong at least you had fun laughing at my jumping to conclusions.
 

shuakarter

New member
Messages
2
Reaction score
0
You are right.

You are right. Larger motor centrifugal clutch and straight chain.
We need a jackshaft or a clutch assembly to get the ratio right or closer. I'm gonna try the link you sent for the place in Houston. Any other suggestions???We don't want to lose the large tires.

Thanks Dave and Joshua Adams

Is this 1/2" pitch or 3/8" pitch?

What size tires are you running?

Just by reading this if I were a betting man I'd take a wild guess you have a Yerf-Dog kart which had a 6.5hp Tecumseh stock which had a 3/4" stock. You didn't think it was fast enough so you put a larger engine 8-13 hp on the kart which resulted in a 1" bore shaft so you could no longer use the 3/4" clutches. Since Comet is out of business you went to buy a 1" centrifugal clutch because you saw the prices on the large torque converters and were turned off, sadly Comet was also the company who made the only 1" bore centrifugal clutch which was also stepped down to 10t, all the other companies Hillard, and Noram who make 1" centrifugal clutches run the shaft of the motor through the whole clutch.This all means you're forced to have a huge tooth count throwing the gear ratio even more out of whack than your 18-20" tall rear tires happen to do. This may be a lot to swallow but I've heard this story before, if I'm wrong at least you had fun laughing at my jumping to conclusions.[/QUOTE]
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
Your post is a bit jumbled, i'm guessing you lost some of the tags for the quoting.

Your two options are a jack-shaft or a torque converter if you choose to keep those tires.

I'm glad this got sorted out for the first problem, and yes the problem is an overloaded clutch russ.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Can you give us some pictures?

Is this 1/2" pitch or 3/8" pitch?

What size tires are you running?

Just by reading this if I were a betting man I'd take a wild guess you have a Yerf-Dog kart which had a 6.5hp Tecumseh stock which had a 3/4" stock. You didn't think it was fast enough so you put a larger engine 8-13 hp on the kart which resulted in a 1" bore shaft so you could no longer use the 3/4" clutches. Since Comet is out of business you went to buy a 1" centrifugal clutch because you saw the prices on the large torque converters and were turned off, sadly Comet was also the company who made the only 1" bore centrifugal clutch which was also stepped down to 10t, all the other companies Hillard, and Noram who make 1" centrifugal clutches run the shaft of the motor through the whole clutch.This all means you're forced to have a huge tooth count throwing the gear ratio even more out of whack than your 18-20" tall rear tires happen to do. This may be a lot to swallow but I've heard this story before, if I'm wrong at least you had fun laughing at my jumping to conclusions.

Yowza , that's a he//uva mouthful to say "dude, you're geared too high."
 
Status
Not open for further replies.
Top