Multiple go kart engine problems

Status
Not open for further replies.

Misun

New member
Messages
9
Reaction score
0
Location
Braham, MN
I've been having problems with a go kart I've purchased recently (used). It worked well when I got it home, though not long after it started wanting to take off the second it was started. It needed to be held from taking off on it's own for a little while. After, it would stand still, idling like it should. Not long after THAT, the driver on the torque converter pretty much fell apart. The thing that expands to pinch the belt (I'm not sure of proper terms, I know very little about small engines, let alone go kart engines. Bare with me lol) won't work properly. It'll expand but won't retract back into the bigger half and just sits loosely on the shaft. Also, when it's idling, it runs extremely rough. Nothing like sputtering or anything but more like... it needs to be tuned or something. It makes the go kart vibrate so bad that it looks like the chassis and roll cage are about to fall apart.

I know I'm being vague about all of this and I apologize. I don't know the engine make or model, same with the torque converter. I'll post an update on those when I can. I mainly just would like to know if these are general problems, if they are easily fixed and if so, how?

I'll try to post pics and vids of the problems if I can, when I can.
 

Misun

New member
Messages
9
Reaction score
0
Location
Braham, MN
Thank you for the quick replies as well as the welcomes c:

So, when I did maintenance on the TC and while it REALLY needed it, it hasn't fixed the grabbing problem. It still grabs, and I have absolutely NO idea how to fix the idle speed. Can anyone point me to a thread or a website that shows me how to do this? It would be greatly appreciated :D

I was able to get it working though by using the driver unit from a different disabled go kart with the same engine (they're the exact same make). Found out why the original driver unit wouldn't stay on.

I took some pics:




The floating sheave won't stay on the four lobed spine (I believe those are the correct terms, lol). Either way, I don't know how to keep these together. The spine can fit back into the hole on the sheave via a small lip but do these have to be wielded? Should they be? The slightest bump and the sheave falls off the spine...

Also, a question about the sprocket on the rear axle... I speak of the giant sprocket on the actual rear axle, not the one that's run by the driven unit. Anyways, how do these tighten on the axle itself? The one on the other disabled kart keeps sliding back and forth on the axle, which has caused the chain to fall off multiple times, as well and break. It's been rendered disabled until I can figure out how to tighten this, other wise fixing the chain will only be a waste of money.
 

souperman000

New member
Messages
2,466
Reaction score
11
Location
Westlake Village, CA
The idle speed can be adjusted by using the idle adjustment screw on uour carberator. Depending on what type of engine you have, It might be at the top. it is teh screw that has a little spring on it.
 

Misun

New member
Messages
9
Reaction score
0
Location
Braham, MN
The idle speed can be adjusted by using the idle adjustment screw on uour carberator. Depending on what type of engine you have, It might be at the top. it is teh screw that has a little spring on it.

Well, I found out that it's idling high because the throttle doesn't return to the state it should be in. It sticks just a bit over the idling position which makes the driver grab just the slightest bit and it goes on from there. Should I grease the lever that keeps sticking? It doesn't look to have been greased ever.... I've sprayed some PB buster on it, though it doesn't seem to have helped. Or should I look into getting a stronger return spring? maybe both?
 

Nissinator1996

New member
Messages
54
Reaction score
0
Well, I found out that it's idling high because the throttle doesn't return to the state it should be in. It sticks just a bit over the idling position which makes the driver grab just the slightest bit and it goes on from there. Should I grease the lever that keeps sticking? It doesn't look to have been greased ever.... I've sprayed some PB buster on it, though it doesn't seem to have helped. Or should I look into getting a stronger return spring? maybe both?

i just put a stronger spring on my throttle to pull it back to the idle posistion when u let off the gas peddle
 
Status
Not open for further replies.
Top