max torque 20 series strong enough?

Status
Not open for further replies.

realfast89gt

Kart Krazy!!
Messages
287
Reaction score
1
Location
cibolo Tx
I have a murray kart with the max torque 20 series tc. I have read about the belt on these kart being too long compared to most other setups. If i have 10-12hp will this tc still be ok, or should i invest in a new one?

Also, what effect does such a long belt have on the tc, and if i do need a new tc will i be able to find a belt to fit?

thanks for any help. :cheers2:
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
IMO:
10HP- Maybe, gear nicely.
12HP- Would not reccomend it.

Check out this for belt lengths, about halfway down the page.
 

realfast89gt

Kart Krazy!!
Messages
287
Reaction score
1
Location
cibolo Tx
IMO:
10HP- Maybe, gear nicely.
12HP- Would not reccomend it.

By gear nicely, do you just mean near 6-1? It is 6-1 right now, but i did order a new sprocket so it will take it to 5.4-1 for a little more top speed.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
How big are your rear tires? Basically just don't nail it, else you will eat belts! If you ask for too much speed with a large engine and low rated clutch, centrifugal type or torque converter type, you will burn something up.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
I would say that would be OK with the 10hp, but cannot be sure, I have never overpowered a tc. Top speed 33mph governed.
 

realfast89gt

Kart Krazy!!
Messages
287
Reaction score
1
Location
cibolo Tx
I would say that would be OK with the 10hp, but cannot be sure, I have never overpowered a tc. Top speed 33mph governed.

Yep, but once i add the offroad cam, valve springs, etc. the rpms will be 5800 max. so this is when i will be worried. I guess when i do the engine work i can try it and see if the tc smokes itself. :wai:
 

brycedevore

New member
Messages
15
Reaction score
0
Have you taken the tc off the crankshaft and if so how I have it halfway off, but can't seem to get the part closest to the engine off?:toetap05:
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
If you start your own thread you will get far more responses.

What engine is this? 196cc Honda/clone?
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
Have you taken the tc off the crankshaft and if so how I have it halfway off, but can't seem to get the part closest to the engine off?:toetap05:

this happened to me once, i ended up having to cut the crankshaft off and replace it. i suggest you start a new thread

@realfast89gt, i would use a 40 series if you plan to go anythting over 10hp. i had a tc on a 10hp(stock) it worked but thats the max power i would put through it. the belt wore much faster than the old 6.5

you may be replacing belts all the time.
 

realfast89gt

Kart Krazy!!
Messages
287
Reaction score
1
Location
cibolo Tx
R Chez: If you were talking to me about what engine it is, i have a tec ohh65.

i would use a 40 series if you plan to go anythting over 10hp. i had a tc on a 10hp(stock) it worked but thats the max power i would put through it. the belt wore much faster than the old 6.5

Now if i did get a 40 series, would it be ok to get a bigger belt, or would i have to modify engine or jackshaft location and use the standard 40 series belt?
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Don't think there is a 'standard' 40 series belt. You do not buy it in a kit form, just individual pullies.
Check out here for belt length.
Didn't realise you could get performance cams and uprated valve springs for the OHH65.
I would say stay with the 20 series for now.
 
Status
Not open for further replies.
Top