Manco Quicksilver 2x6 GL Engine Mod

Status
Not open for further replies.

MikeinMadison

Member
Messages
42
Reaction score
1
Hi all
I sincerely appreciate any help!

I have a buddy who needs an engine for his kart and figured I might upgrade to something more powerful and give him mine. I currently have an EX17 in my Manco go kart.

The question:
If I want to go with Robin again, what would you recommend and what do I have to do to make the 7, 9, etc. hp Robin engines work with the kart?

Thanks for any help!!
Mike
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
Before we suggest an engine, what kind of clutch do you have at the moment? Is it a 30 series/TAV2 torque converter?
 

MikeinMadison

Member
Messages
42
Reaction score
1
It's a Comet Series 30 TC (Asymmetric). I'm not sure about the tav2 designation. The kart is probably 7-9 years old, if that helps.
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
With that TC, you can't do much more than 8hp as it's only designed for 8hp and will devour belts with any more hp being put into it. :(
 

MikeinMadison

Member
Messages
42
Reaction score
1
Thanks redsox985
So would I be able to bolt an EX21 right up to it? Also, if I wanted to go with more hp, say 9, what torque converter, etc. would I need?
Thanks!
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
if your looking to upgrade engines(in the Robin EX series, which are awesome!), these are the options that would make the most sense:

- get EX21 (7hp) which should bolt directly onto your setup (you will gain 1.3 HP)
- get EX27 (9hp) then modify mounting plate and jack shaft. then buy a 40 series torque converter.
_____________________________________

you could also:

-keep your engine and modify it (would make it maybe... 7hp? but causes excessive wear and would void your nice 3yr warranty(be better to get EX21))
-change gear ratios to better suit your needs (you can sacrifice acceleration for more speed, or speed for more acceleration)
-get EX27 and a cent clutch (or belt tensioner) so your buddy gets an engine, and you can still ride until you get a 40 series. (you could likely loose performance, but it might work out better for your buddy and would ease the pain in your bank account)
_________________________________________________________

if you want the performance and have the money,
- get EX27 (9hp) then modify mounting plate and jack shaft. then buy a 40 series torque converter.


heres some good deals,

awesome deal! http://cgi.ebay.com/Robin-Subaru-Engine-9-HP-Free-Shipping-/300565633282?pt=LH_DefaultDomain_0&hash=item45fb1b9902#ht_657wt_905

http://cgi.ebay.com/Robin-Subaru-Engine-6-HP-Free-Shipping-/290569153122?pt=LH_DefaultDomain_0&hash=item43a7456a62#ht_637wt_905

http://cgi.ebay.com/Robin-Subaru-7-HP-EX21-Engine-/150336057665?pt=LH_DefaultDomain_0&hash=item2300ba3141#ht_500wt_922

P.S. from what i have read, if your really interested in modifying stuff (doesn't sound like you are, but anyway) i have read that the EX21 is best. of course o some research before dropping $400!
 

MikeinMadison

Member
Messages
42
Reaction score
1
Thanks for the input!

Perhaps I should have went with the ex21 but that ex27 for under 300 clams was too attractive. So, I bought it.

So I need a series 40 TC and need to modify the mounting plate and jack shaft ... can you give me a quick run through of what I'd need to do to mount it and mod the jack shaft? (and/or if you know of links to websites with the necessary steps/issues/etc.)

Thanks again!!
Mike
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
you bought it, already? Dang!

well i guess your committed now, LOL!

your going to need to:

the new engine will have different bolt hole locations, so you are going to need to either drill new holes in the existing plate, or weld in a new plate. you may also need to move the plate around so the engine fits in the frame, has proper alignment with the Jack Shaft, has proper spacing for a standard belt, and is strong enough to handle the larger engines power.

the jack shaft might need to be moved over, lengthened, and maybe upgraded to 3/4". you should also install an outboard support bearing on the jack shaft.

as for the torque converter you can either:

1. search E-bay and craigs list every day for a used one.

2. risk it and buy a GTC industries 40 series copy (clone, knock-off, ETC). no one has experience with this specific model GTC clutch, but most agree comet is probably better.

3. contact go kart suppliers to see if they have any 40 series in stock, just because its listed on their site doesn't mean they actually have them. look around the forum, this has been discussed lately.

I'm jealous of you and you engine with 3.3hp more than mine! LOL
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
I think the JS he speaks of is in the back plate of the 30 series TC. For the 40, you will need to mount your own JS, usually with pillow blocks, and then buy a belt for the center distance from the PTO to the JS. Who was that that set up a really nice JS on a Briggs V-twin? I want to say killdozer, but I know he's the sled cradle guy.

EDIT: It was StratoGeezer! I found it. Check out his video showing a nice 40 series and JS setup.
http://www.youtube.com/watch?v=ii8v11U4hBg&feature=player_embedded#!
 
Status
Not open for further replies.
Top