Making a new go kart!! :D

[Go kart builder]

Hello!

First, I would say that I can't good write english.

I would make a new go kart for my.
I must be a go kart not to big and not to small.

For the backside I'm thinking about this stuff:

-A B&S 4Hp motor.
-This axle:
http://www.mfgsupply.com/m/c/AZ1401-34.html?id=B4qaWh24

This brakes:
http://www.mfgsupply.com/m/c/4-488.html?id=B4qaWh24
http://www.mfgsupply.com/m/c/AZ1823.html?id=B4qaWh24

This sprocket:
http://www.mfgsupply.com/m/c/AZ2092.html?id=B4qaWh24

Wheel hubs???

I need wheel hubs with 3 hole but I can't find it on that website??

Clutch???

I need a clutch for my B&S motor.
Its a motor like the most of members on this website use.

I don't think that I need more for the backside??
When I need more?
Could you say me what I need more?

For the frontside I don't know how to do it...

What do I need all??

I need spindles??
I need new wheels for that spindles??

What do I need more for the steering??

Thank you for your help.

 

[anderkart]

-This axle:
http://www.mfgsupply.com/m/c/AZ1401-34.html?id=B4qaWh24

Wheel hubs???

I need wheel hubs with 3 hole but I can't find it on that website??

I found some 1" axle / 3-stud hubs that might work for you here:
http://www.cometkartsales.com/store/wheels/vankhubs.htm
(3rd hub down on this page / Circle Wheels 1" Hub $17.50)

Just keep in mind theres serveral diferent 3 bolt wheel pattern sizes made, so you should mesure your rims bolt pattern (and center hole) and then email/call Comet and ask if their hub for a 1" axle will fit your rims.

 

[Go kart builder]

Thank you for your reply!!

I'm thinking to combine this all:
http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_24007_24007

http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_200304625_200304625

Is this compatible with the wheel hubs you give me?

http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_23630_23630

http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_35624_35624

http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_35774_35774

http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_21915_21915

http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_20861_20861

http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_35036_35036

http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_200331207_200331207

http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_200321704_200321704

http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_35774_35774

http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_35624_35624

I would make the frame self and use this all.

Is this all what I need??

 

[anderkart]

The rear (3-bolt) hubs I suggested are made for a regular 1" axle that just has 1/4" keyways machined into each end like the un-threaded axle pitched here: http://www.mfgsupply.com/m/c/AZ1401-34.html
These race kart style hubs have (Allen bolt) clamps built in to hold them to the axle and dont need an axle with threaded ends.

All your other parts look ok accept the rear sprocket you picked doesnt seem to fit the sprocket hub you selected.