Lost

Status
Not open for further replies.

Fistral

New member
Messages
5
Reaction score
0
I just got a cart frame that had no motor:
back wheels are 18 1/2 -19 inches high
chain on axle is 34-35 in long

So I bought a new 6.5 motor with a 3/4" shaft and 3/16" keyway shaft end (whatever that means).
Also a 5/16" - 24 UNF (again no idea?)

Can you tell me what clutch size I need for it and what the different tooth numbers mean. I assume torque vs speed?
I only got this for a father son project so we don't need the high tech stuff. I had a go cart when I was his age and wanted him to have one.

Thanks,
JD
 

Badot

New member
Messages
677
Reaction score
2
The 3/16" keyway is a slot on the engine shaft (the clutch/sprocket you put on the shaft should have a matching one) where you basically cram a piece of 3/16"x3/16" square steel in there to keep it from spinning freely. The 5/16" - 24 is the size and pitch of the hole in the end of the shaft for a bolt so you can keep whatever's on the shaft from sliding off (set screws work for this as well)

A 3/4" bore clutch with a 3/16" keyway is what you want. 'Tooth numbers' can refer to a few different things... If it's say a #40 sprocket, the #40 tells you the specs of it and what chain to use. The number of teeth on the clutch sprocket (paired with the number of teeth on the axle sprocket, as well as a jackshaft if used and the size of the wheels) gives you your torque/speed tradeoff.

To start, can you measure the distance between the pins on your chain, center to center, and the width of the rollers (sleeves on the pins, distance between the flat sides)? Also, I assume the chain fits the sprocket on the rear axle? Your number of teeth on the rear sprocket would help as well, and your jackshaft if you have one.
 

Fistral

New member
Messages
5
Reaction score
0
Great starting point for me. I am glad you explained it in an elementary level. I'll get to work on the information. Unfortunately I have no idea what a jackshaft is, where it is, and what it looks like?
Thanks for all of your help.
JD
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
heres a jackshaft on one of my projects. basically a keyed axle with 2 sprockets and no tire. you can use them to relocate the chain (as i am) or to reduce (or higher) the gear ratio, or both.

 

Fistral

New member
Messages
5
Reaction score
0
Sorry, but lost has a few meanings!

OK;
The tooth count for the rear sprocket is 60.
The number on the chain is 40.
There is no JackShaft (but I do understand what its function is now)
and the Axle is not live.

Now....
What Clutch do I need for the cart to have medium speed and good torque?
Thanks
 

Fistral

New member
Messages
5
Reaction score
0
Why would you expect something about a TV show on a cart message board.....maybe Im not the only one who is lost :)
 

Badot

New member
Messages
677
Reaction score
2
#41/40 clutches for 3/4" engine shafts typically have 10 teeth, so with 19" dia. tires and a 60t rear sprocket you're looking at a top speed of around 34 mph at 3600RPM (what your engine is governed at)

I don't have experience with CVTs, but that seems to be about the proper range for one.

If you want to use a centrifugal clutch, I would suggest regearing the kart. You'll most likely want to install a jackshaft, however you may be able to get away with reducing the wheel diameter if you have a light kart/rider and are riding on fairly flat/smooth ground.
 
Status
Not open for further replies.
Top