Looking for Help Identifying this go kart

Status
Not open for further replies.

ZR2Chevy22

New member
Messages
20
Reaction score
0
Location
Kemah, TX
I got all the stuff I need in my RC bin.. Mine is good for line of sight. No need in buying it when I have all the stuff to make it.

Yep yep.... Gotta keep the kiddos safe. They sell cheap remote kill kits for karts/atvs for like $50.... I'll find a link..... I think they are good for 200-300 feet though....
 

firemanjim

Just kartin' around....
Messages
5,247
Reaction score
88
Location
Houston Texas
I got all the stuff I need in my RC bin.. Mine is good for line of sight. No need in buying it when I have all the stuff to make it.
O really? Enlighten me o wise one.... O he(( it just hit me.... I can wire a servo to act as a kill switch, grounding out kart ignition.... Right?
 

ZR2Chevy22

New member
Messages
20
Reaction score
0
Location
Kemah, TX
Nope.. in theory it's just a little electronic relay of sorts. When open allows the motor to operate as normal. When you send a signal to it using the RC controller through the receiver, it "switches" closed grounding out the ignition killing the spark. Simple as that.

I use one on my 1/5th scale gas buggy that uses a modified 26CC weed eater motor and it works like a charm.
 

firemanjim

Just kartin' around....
Messages
5,247
Reaction score
88
Location
Houston Texas
Ahh, can you post a link to what I need? I got a controller and receiver (where did my son put his rc car? LOL )
 

ZR2Chevy22

New member
Messages
20
Reaction score
0
Location
Kemah, TX
In all honesty if your wanting to put a remote kill on something go with the kit that's out there. Even having the transmitter and receiver it would still be between 60-70 bucks. I just had all the stuff off an old car.

Andrew
 

ZR2Chevy22

New member
Messages
20
Reaction score
0
Location
Kemah, TX
Hey Jim you know anyone who does wire welding? It's looking more and more like the buddy that was gonna do it for me is going to flake out on me.

What I'm needing is to have the floor board retacked into place. It's lose up near the pedals and needs to be retacked in a few places. I also want to weld on a peice of angle iron which I have cut to size ready to go, to the front square bar that the spindle brackets mounts to to straighten it back out and stiffen it.

Andrew
 

firemanjim

Just kartin' around....
Messages
5,247
Reaction score
88
Location
Houston Texas
Well, if you can bring it to my shop Saturday, it could be done free. (I'm not stingy) but half way between you n me, is discount go karts of Texas. They will tack it up pretty cheap. Good folks over there.... Any muffler shop will do it for a couple $$ but then again, a man in uniform (badge) gets perks others don't. (I turn down free food, service, whatnot all the time) Drive by one and ask the manager (while your still in uniform) and ask about getting the kart welded. He will tell you no problem, no charge.... Bring it by any time.....
I will admit that I accept the GRACIOUS Discount I get on used (almost new) tires from a place in my district. They know I use my truck to respond to calls from home. I live on the north side of my district, my station is on the south. I will respond from home to medical calls and fire/mva's on this side when time is of essence.....The brush is rough on my tires too. Wish I could run them GOVERNMENT humvee tires.... $900 each.....
EDIT... My shop is @ 288 & beltway 8 just in case.....
 

ZR2Chevy22

New member
Messages
20
Reaction score
0
Location
Kemah, TX
Well I work this weekend so that would be out. 6pm-6am Fri-Sun. Get every other weekend off. I also don't accept free stuff. I worked IA in the past and did new hire orientation and preached about not being above anyone else and why should you get something the old guy in the corner who fought in wars doesn't get.

I'm gonna see if he might come through with his offer but if not I may go pay Discount Go Karts of Texas a shot..

Andrew
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
FYI: Go karts of Texas is run by the family of one of our members, Blazkowiez. Granted, he hasn't been here for a while but, I'm sure, if you mention this forum, it will make a difference...
 

firemanjim

Just kartin' around....
Messages
5,247
Reaction score
88
Location
Houston Texas
:thumbsup:well, anytime you wanna/needa play with a wire feed, let me know. id even loan it to ya for a weekend if need be. I am fairly confident I'd get it back.... :cheers2:
 
Status
Not open for further replies.
Top