Keeping a Predator 212 quiet

Status
Not open for further replies.

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
Also along the lines of my suggesstion. Roll up to Post #18 here. That is a really nice Kart. DHC knows his stuff. but my point is, in his pic you can see the muffler. that is just a stock Briggs and stratton muffler available on Ebay 8bucks. He is running a High performance engine through it. Other than Higher RPMS "if" your governor is removed, a muffler like his or mine will not be louder than a lawnmower. and His at least proves it works with High output modified small engines. Mine just has that muffler and an intake.
I think it is the pipe. As mentioned before, the stock muffler is attached to a short tiny pipe that is ovalled to be even smaller.
 

Jrgunn5150

Rudderless
Messages
1,028
Reaction score
12
I never thought of the governor being a factor. I had that muffler, I thought it was loud, and it was in the way and looked dumb so I cut it off lol.
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Well....as I alluded to originally...the biggest problem is not what happens AFTER the exhaust gets to the tailpipe...(header, muffler....whatever...) but the mismatched port to muffler setup on the stock Preadator....

In the simplest terms....engines are simply air pumps...the more air you can move in and out....the better.

However, to understand it more easily....it helps to imagine fluid moving through the system...and a funnel...or pipes that get smaller....now....we've all poured stuff in a funnel....and you can pour a max amount in and it drains pretty quickly....but dump in more than that...and it cuts off the air...and it drains slower....getting a larger funnel with the same sized small spout and dumping even more fluid in all at once doesn't help at all.....

On a Preadator the exhaust port is bigger than the exhaust pipe....and it causes turbulence and hinders air exchange through the engine.....

It's really that simple...no dynos or experimenting necessary....just simple mechanics and time proven laws of engine operation.
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
Just for fun: here is a pic this is a stock muffler with the flange removed, next to the Exhaust port It came off of.
Tiny restrictive stock pipe
 

Attachments

  • IMG_1897.JPG
    IMG_1897.JPG
    130.7 KB · Views: 8

FreeRunner15

=======
Messages
660
Reaction score
10
Location
================
Did someone say "muffler" ?

 

jrm189

New member
Messages
6
Reaction score
0
All good information! So if these engines do come lean from the factory with a .7mm (.0275) main jet, what would be a good size to start with in re jetting it to run a bit more like it should, which should also help keep it a little cooler?
 

Jrgunn5150

Rudderless
Messages
1,028
Reaction score
12
All good information! So if these engines do come lean from the factory with a .7mm (.0275) main jet, what would be a good size to start with in re jetting it to run a bit more like it should, which should also help keep it a little cooler?

Well, since most of us are running something from 35-37, with the full monte upgrade. If you wanted to experiment, I'd start at .030 and go from there. Since you can always drill it larger, but it's tricky to make it smaller lol.
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
Also your local lawnmower shop may have a bunch of extra Jets in the mechanics back drawer, they may just give them to you.
Or even an entire kit of jets is not real expensive. Just read the plug and swap the jets as needed.
 

DHC

New member
Messages
111
Reaction score
4
Also your local lawnmower shop may have a bunch of extra Jets in the mechanics back drawer, they may just give them to you.
Or even an entire kit of jets is not real expensive. Just read the plug and swap the jets as needed.

... and if no luck there... a drop of solder, in the hole, and drill out proper sized orifice/jet. Ive done it to 3 different engines (all in the reasoning of trial n error)... worked for me.
 
Status
Not open for further replies.
Top