Installing Comet 40 on EX27

Status
Not open for further replies.

metalthrashinman

New member
Messages
279
Reaction score
0
Location
Hope, NJ
I know the site went down. Blaz, can you post those pics again of that plate and the TC? I wasn't through with them yet! Thanks!

For all who did not read the previous accidentally deleted thread (that had a ton of good info), my GTC Tav 30 cannot handle my Subie Ex27 without burning belts. We were close to a solution when, as the mods put it, KAPUT!
 

metalthrashinman

New member
Messages
279
Reaction score
0
Location
Hope, NJ
I got stuck in the snow the other day because my TC is junk. Motor was pulling and belt was burning. I installed my new sprocket, and I'm still smoking belts. :worried2: In fact, I have a graveyard of belts that has 9 buried (in 6 months) and is growing fast.

I am running the 9 hp Subie EX27 with 18" rear tires, 8 tooth front sprocket, 54 tooth rear sprocket, on the :2guns:GTC 30 series that I read was good to 13hp. I am very unsatisfied with the poor shifting, belt burning, money and time wasting, poorly built GTC that I was suckered into buying by reading lies torque converter. I have a Comet 30 that is on a different kart, so I know quality when I see it. I should sue GTC for FALSE ADVERTISING!

Anyway, now I am looking for a Comet 40 series so I can finally get it right.
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
Here are the pictures I had before, dang crash.

Series 40 requires little if any maintenance aside from blowing out with air. The belts last 2-3 years compared to series 30 which last 10 months with similar operation. The assembly can handle 25hp without any issue where your series 30 is having trouble with 9hp?
 

Attachments

  • box1.jpg
    box1.jpg
    84.1 KB · Views: 10
  • box2.jpg
    box2.jpg
    88.5 KB · Views: 10
  • box4.jpg
    box4.jpg
    146.9 KB · Views: 10
  • box3.jpg
    box3.jpg
    152.1 KB · Views: 9
  • box5.jpg
    box5.jpg
    154.7 KB · Views: 8
  • box6.jpg
    box6.jpg
    85 KB · Views: 11
  • P1010203.jpg
    P1010203.jpg
    143 KB · Views: 11
  • P1010221.jpg
    P1010221.jpg
    120.9 KB · Views: 12
Last edited:

metalthrashinman

New member
Messages
279
Reaction score
0
Location
Hope, NJ
What kind of gearing do you recommend with this set up? I have a 40 tooth rear sprocket, a 54 tooth rear sprocket, and a 60 tooth rear sprocket - all ready to go and are all moderately easy to change out. 18" tires, and EX27 9hp motor that seems under-rated because of how it will rip a 30 series beyond it's abilities even with very conservative gearing. What sprockets would you use (front and rear) considering some hill climbing, quick acceleration desired, and a maximum top speed to make your eyes water?
Is the driven a 7"?
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
With a 60t rear sprocket and a 10t jack-shaft sprocket you'd have excellent torque and the power of the engine should compensate to leave you with a great top end specially since its a Subaru.

However if you wanted more top speed you could try the 60t rear at first and switch it up if its not fast enough for you.
 

metalthrashinman

New member
Messages
279
Reaction score
0
Location
Hope, NJ
I would like to be able to run the 40t rear on a 10t front with the 18" tires on the 40 TC. Whatcha think of that? Could go to a 9t or 8t on the front as well...:confused:

Stock was 10t front 60t rear on the 18" tires with the 169cc motor. About 40 mph.

I have read that the Subie motors are governed to 3600 rpm, correct? So the 265cc motor would not be faster than the original setup geared the same way, but would have more power. Correct? I want more top speed that is dependable -- without toasting the belt.

Which brings up another question of how to get more out of the engine...
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
I have no idea about the quality of the guts but I'd assume it's good. Better intake and exhaust which would require a rejet so maybe a better carb. Pulling the gov. would give you the speed you want with the lower ratio for torque too. That could be a major win. Higher rpms and top speed with a low gear ratio to get off the line quickly.
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
I wonder what a bigger carb would do to a Subaru like that... I've seen what a wicked Mikuni can do to a GX270, I'd like to see what the Subaru counterpart could do with a comparable carb.
 

metalthrashinman

New member
Messages
279
Reaction score
0
Location
Hope, NJ
I need to get this TC problem sorted out, and then work on the engine. This thing needs to be wild enough for me to say WOW!

I am willing to put more into the motor to get what I want. I never quit until I am satisfied.
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
You should consider getting better tie rod ends for the front end at these speeds btw, if one breaks going 50 you're toast.
 

metalthrashinman

New member
Messages
279
Reaction score
0
Location
Hope, NJ
You should consider getting better tie rod ends for the front end at these speeds btw, if one breaks going 50 you're toast.

I like toast... :roflol:

Let me know what you mean (pics, plz). I do plan on welding some supports soon. I have learned a lot from reading around here.

In the end, I desire a unique kart that is dependable, safe, and 'knock your socks off' fast. I will not quit until this is achieved.
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
Rip out the gov. to start. You won't get those speeds you want with that bugger in there.
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
I hardly see a reason to remove a governor unless you plan to go 5k+ rpm, it shouldn't rightfully hurt anything to bypass it with the new carb if he does plan to upgrade in the future. Its unlikely the linkage would run through the governor rod at that point bro.
 
Status
Not open for further replies.
Top