i need help with gear ratios! :(

Status
Not open for further replies.

Mrpinhead11

New member
Messages
62
Reaction score
0
Location
ebensburg pa
alright so the ratio i run now is a 9 tooth on the tc to a 38 tooth rear with 17 inch tall tires, i burn belts like nothing.
Now if i get a 54 tooth rear sprocket will that corect my impropper gear ratio or should i go bigger? thanks and marry christmas! :)))))
 

Banditz

New member
Messages
42
Reaction score
0
Location
Mt. Pleasant NC
Yoru thinking right..The bigger you go back there the slower the cart will be, but the faster she will get up and go and more tq you will see off the line. The key is having enough tq to get you going without any major slipping, yet at the same time also give you a good top speed that makes it fun for you. No one wants to go 5mph on a kart top speed. lol. then again, no one wants to go 50mph either unless there cart is MADE for that kinda speed. Mine i run a 9 tooth up front with a 60 in the rear. And of course a Tq converter. This enable's my fluffy butt to do burn out's at will and donut's with ease, yet at the same time have a top speed of around 28 or so..but getting there is SO much fun! Hill's are NO problem at all for my baby.
 

Mrpinhead11

New member
Messages
62
Reaction score
0
Location
ebensburg pa
id be happy with that top speed. but the belt always slips the way it is now. do u think if i get the 54 tooth sprocket, will it be better?
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Much better. But whether it's "best" depends on some other factors. Kart type and intended terrain, weight (including you), max engine RPM, etc are important factors.
 

Mrpinhead11

New member
Messages
62
Reaction score
0
Location
ebensburg pa
alright its a homemade offroad gokart. it weighs around 150 pounds plus me so around 290 with all my gear tools and other stuff. it runs around 3600 rpm but imma remove the govenor and i take it up hills and offroad. i had a yerf dog 150cc gx and it ripped tits. i wish i kept it but it was a money pit
 

Banditz

New member
Messages
42
Reaction score
0
Location
Mt. Pleasant NC
If your going up hills and off road with it I would think you would want more than the 53 back there...A 60 would be nice like I have. Your a bit lighter than me so the smaller gear would maybe be ok. But if you really want to climb some hills and have no problem on the bottom end i would go with the 60 or larger.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
If you're planning on removing the governor, go ahead and gear lower. Banditz is suggesting 60T, which would give you 6.66:1. I assume you have a CVT because of your comment on burning belts.
 

Banditz

New member
Messages
42
Reaction score
0
Location
Mt. Pleasant NC
Yep, 6.6:1.. figured with the size tires he is running that being geared high like that would be great since he's going off road and climbing hills. With my cart I have 15" tall tires and that same set up with the TQ. With that I can do donuts unlimited, climb most hills, and still have my decent amount of speed. All with me weighing in at about 120lbs MORE than him! LOL basically it's like there are TWO of him on my cart. So yeah, if that's what he is wanting to do climb hills, go offroad, and have basically unlimited tq with his setup i can't see how a 60 would hurt him at all.
 

Mrpinhead11

New member
Messages
62
Reaction score
0
Location
ebensburg pa
well i use a 110cc atv axle and its a splined keyway unstead of it bing the normal way so the sprocket hub only fits certin sprockets but the bigges one i found is a 54 so the 54 will have to do.
 
Status
Not open for further replies.
Top