How does this rear axle come off???

Status
Not open for further replies.

97cobra

New member
Messages
8
Reaction score
0
I've had this "amusement park" style go kart (9 hp Honda with a 6:1 gearbox) for a few years now. Heavy duty frame!! The problem is I cannot figure out how to remove the rear hubs or 8mm sprocket assembly. There are no set screws? It is a live axles with 3 bearings. I have beat on it, tried using pulley removers and beta on it some more with no luck. It appears this has to come apart because there is a band break hub that is bolted to the 8mm sprocket. Does anyone have a clue how to get the hubs and sprocket off? The reason I'm trying to remove the axle is I have a 13hp Honda to put on it but it does not have a gearbox so I purchased a chain clutch and chain sprocket. HELP!!
 

Attachments

  • ministang.jpg
    ministang.jpg
    73.6 KB · Views: 19
  • 051811_1714[1].JPG
    051811_1714[1].JPG
    172.1 KB · Views: 22
  • 051811_1716.jpg
    051811_1716.jpg
    66.2 KB · Views: 25
  • 051811_1714a[1].JPG
    051811_1714a[1].JPG
    168.4 KB · Views: 22
Last edited:

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
can we get a better pic of the axle

it isnt one of those twist type lock collars (it will have holes with no thread in the side of it)?

if u are sure there are no set screws then try ozying the hub slowly to warm it up
it might just be press fitted

is it keyed or just slid on there?
 

Fantic-guy

New member
Messages
65
Reaction score
0
Location
South Westren Ontario Canada
Do the various hubs have bolts around the hub close to the center? On my kart the sprocket and brake drum have keyed compression inserts. The hub(s) is two piece, the part the sprocket bolts to and an insert with blots going through it. When you tighten the bolts it squeezes the insert and clamps onto the axle Dunno if this is what you have but it's one type of hub to look out for.
 

97cobra

New member
Messages
8
Reaction score
0
I've added a few more pictures that I hope gives a better idea of what I have. The axle is not keyed. I'm stumped.
 

97cobra

New member
Messages
8
Reaction score
0
Thanks for the info. Since this go kart was once at a an amusment park it's built to last. Heavy duty frame. I can't imagine they desiged these things so that the axle cannot be removed. Take a look at the sprcoket setup picture I added. There are no set screws on it either so what keeps it from slipping or moving from side to side?? I'm hoping someone out there has a go kart from an amusement park and has worked on these. Thanks for looking.
 

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
try heating up the hub with an oxy accetolene torch then hitting it off

is there a serial number on the frame
who makes it
can u google the name
 

97cobra

New member
Messages
8
Reaction score
0
The bolts you see are for the band brake. My concern is I don't want to keep beating on it and screw it up. Worst case is I could buy another axle I guess. My goal was to swap axles with the 2 seater I've been working on for my kids. I have a new 1" axle, sprocket and brake set up for it. Since the concession go kart is so heavy I'd like to put the 13hp motor (Close to new condition) on it and put the 9hp on the 2 seater. Something that seamed so simple is a real pain in the _ss.
 

97cobra

New member
Messages
8
Reaction score
0
Thanks for the web pages. I did find a go kart that looks similiar but they don't give no details.
 

oldbikerarlo

Old guy
Messages
449
Reaction score
2
Location
Marana, Az.
Have you tried letting the air out a tire and taking the wheel apart from the hub. The hub looks like it might be a taper lock type.
 

97cobra

New member
Messages
8
Reaction score
0
WOW is all I can say. Finally figured it out. This is actually a 2 part axle and just like oldbikerarlo said each end is tapered as well as where the axles connect at the sprocket. I added some pictures. After removing the 4 bolts that mount the band brake hub to the sprocket I turned one of the wheel hubs and noticed the other hub didn't turn. Now all I need to do is replace the belt style sprocket with a chain sprocket BUT of course there is a problem. The sprocket "center hole" has to be at least 3.25" and a 4 bolt 2 7/8 bolt pattern. I've been searching and found sprockets with a 2 7/8 bolt pattern but not a large enough center hole. Always something. I think it will be best to leave this axle on this go kart since it needs 3 bearings due to being a 2 part axle. I have a chain sprocket I purchased for the other go kart 1" live axle but it is the type that uses a key and hex screws. I was thinking of cutting a center hole and drilling 4 bolts holes but cutting that center hole won't be easy. Any suggestions??
 

Attachments

  • sprocket.jpg
    sprocket.jpg
    71 KB · Views: 6
  • right_side.jpg
    right_side.jpg
    72.8 KB · Views: 8
  • Left_side.jpg
    Left_side.jpg
    58.9 KB · Views: 7
  • 2part_axle.jpg
    2part_axle.jpg
    70.8 KB · Views: 6
  • 2partaxle.jpg
    2partaxle.jpg
    64.2 KB · Views: 8

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
The sprocket "center hole" has to be at least 3.25" and a 4 bolt 2 7/8 bolt pattern.

Any suggestions??

Measure your sprocket mounting hole pattern from any 2 holes all the way across the center hole. (and very accurately measure this pattern from center to center just like you would when sizing a car rim bolt pattern)



Some replacement sprockets are indeed measured/marketed from 1 mounting hole over to the one right next to it, but the bolt-mounting pattern of many others are measured/marketed like I suggested... You have to be able to tell what specs they're quoting. If your unsure, email them asking.

These 2 on-line suppliers have LOTS of different/odd-ball sprockets available:
http://www.gokartgalaxy.com/sprockets_&_sprocket_hubs.htm
http://host0114.csmhosting.com/iw_products.m4p.pvx?;products_no_tree?company=APS?CAT=SPR
 
Status
Not open for further replies.
Top