how do i advance timing?

Status
Not open for further replies.

eastereggsrus

New member
Messages
22
Reaction score
0
I read everything about timing I now I can file down a key but where is it? I now its by or on the flywheel somewhere, and How much do I file down I now its like .006 for each one but I don't have a ruler that says .006 on it, I was thinking if I wanted 6 advance that would be like .036 or something like that witch is almost 1mm so can I measuer 1mm on a ruler and shave it a little less? I have a L shaped metal ruler thing and its pretty acurate, I searched everywhere and can't seem to find a pic of it on the motor just a little piece of metal and that doesn't help much thanks and sorry if I seem stupid I just can't seem to figure it out by the way its a 6.5 hf clone thanks
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
The flywheel key is a length of square steel 3/16" or 1/4", an inch or so long, and is used to index the flywheel to the crankshaft. When you remove your flywheel, you'll see it sitting in a square groove between the flywheel and crankshaft.

If the engine is still stock, advancing the timing will not help you.

The L-shaped metal ruler thing is called a square, and is NOT at all appropriate for this sort of task. You need a micrometer. anything else is just guesswork.

BTW, you CAN buy timing advance keys....
 

eastereggsrus

New member
Messages
22
Reaction score
0
I got a a filer, exhaust, 140 etube, drilled main jet and I'm gona set my governer to 4500 as soon as I get my rpm gauge hooked up soon I'm gona get a rod
 

slideways

New member
Messages
575
Reaction score
6
I believe totally in doing things yourself but for this i can honestly say you should either just buy an advanced key from somewhere like affordablegokarts, nr-racing.com or american power sports. Otherwise find another stock clone key and experiment a little with that one. Because you can't really go back if you mess it up.

And DONT hit the flywheel with a hammer when you take it off. Gently pry evenly around it while tapping the nut that is loosened. You will take off just enough material that you can barely tell. Think about this.. the flywheel is 360 degrees.. you need to take off about 2 or 3.
 

eastereggsrus

New member
Messages
22
Reaction score
0
I have a gx140 parts motor so I have 3 ooptions
Use the 140 key to expriment with
Take the 140 flywheel to a machine shop and have them fit it on my clone
Just buy an advance key
So my question is I now the 140 flywheel won't fit but its the same size and eeverything as the clone just needs to be honed out, is the 140 aluminum? And will it advance the timing? If so ill just go to a maching shop and have them fit it on then I would kill 2 birds with one stone, an aluminum flywheel and advance the timing
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
Very little changes from a 5hp Honda to a 6.5hp Honda. However I'm not sure what internal parts are compatible from 5hp Honda to 6.5 Clone. Mainly when you look into the internal parts you'll notice differences in the Head and the Carb. I'm not saying those are the only differences but they are not very different engines from the block up.

The flywheel will not be aluminum assuming the 140 is stock. This is a horizontal GX series correct?

The gentlemen who posted earlier had the correct idea, for cost and correctness you'll want to buy an advanced key.
 

slideways

New member
Messages
575
Reaction score
6
I'd just get an advanced key. I am not positive but i think the 140 doesn't share parts with the 160 or 200. I think its a smaller setup like a 4.5hp. The e-tube is probably the only thing along with some other little parts that will work. I wouldn't trust a machine shop to match a flywheel up. Unless its a cast aluminum unit which i believe were only on the GXV push mower engines it won't help you anyway. The slightest mismatch or balance issue could be a catastrophe.

I really doubt you will feel this mod in the seat of the pants but its one of those things you just know its there and available to you as you go bigger and better with the motor.
 

eastereggsrus

New member
Messages
22
Reaction score
0
http://karting.4cycle.com/archive/index.php?t-210030.html I was reading this, it is llighter and oem honda not a knock off and the maching shop will do it for 10 bucks is it worth it? It also gives a 4 advance just like a 160 but for 10 bucks think its worth it? I don't really want to blow hella bank on aluminum flywheel so I think this might be worth it, how much does a timing mkey cost?
 

Imbo

Young Mechanical Genius
Messages
263
Reaction score
0
Location
Garden City, NY
hey guys. I noticed this threads about timing advance the key or something. this is one thing i really dont understand. What is this advance doing.....please explain!:huh: haha thanks guys
 

slideways

New member
Messages
575
Reaction score
6
I see that thread but nowhere does it say that it worked or that the flywheel is lighter than the stock one. I'll tell you this though.. i'm quite well read on the whole clone racing movement and if the GX140 flywheel was an upgrade over the clone/gx200 unit people would be going nuts trying to find them. They arent. They are either going with the ARC unit for $100 bucks or finding the Honda GCX one from a push mower which are also around $100 to buy. The key here is safety over 5000rpms. The stock flywheels are not safe up that high so guys just buy the ARC one and sleep easy. The aluminum honda version isnt safety certified but is about 4 oz lighter than the ARC one so if you are eeking the last spec of power out of a race motor it may be worth it.
 

Routy

New member
Messages
213
Reaction score
0
imbo, combustion in the engine takes a certain amount of time, so you advance the timing so when the piston is compresing the fuel air mixture, the spark plug will ignite the mix a certain degree before tdc (top dead center of piston) so the fuel takes its time to burn and by the time the piston is at tdc its at full power from the caboomb! lol thats the basics. And i thought that you could change the timing by moving the magneto over a little. or does the magneto not move side ways.
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
http://karting.4cycle.com/archive/index.php?t-210030.html I was reading this, it is llighter and oem honda not a knock off and the maching shop will do it for 10 bucks is it worth it? It also gives a 4 advance just like a 160 but for 10 bucks think its worth it? I don't really want to blow hella bank on aluminum flywheel so I think this might be worth it, how much does a timing mkey cost?

Dude, kudos to the people who have spent insane amounts of time comparing these parts.

Sorry I was wrong with what I said there. I was looking at a laminated breakdown of the motors trying to compare :p We rarely see the GX140, the sales versus GX160 & GX200 appears to be very weak in what we've seen come back into the shop on karts.

Tell us how this turns out.
 

Oldschool Briggs

New member
Messages
1
Reaction score
0
Advancing timing

Here is how we acheived advancing the timing. I used to build Briggs kart engines years ago. I did what everyone else started out doing, using an offset key. Then as I got older and wiser and kept my mouth shut and ears opens I discovered some were lapping the flywheels to the crank shaft with fine valve grinding compund. You will see the crank turn grey as they come into perfect mating alignment. Then you don't use a key at all. It will not slip when it is tightened up. The trick is to get it into the correct position before you tighten it. We used a timing degree wheel from a automotive store that is used to degree cams in during assembly. If you know someone at a machine shop they can mark off your flywheel in degrees for you too. You just get the piston at the top of it's stroke and rotate the flywheel however many degrees you want in the direction the engine turns while running and tighten down the flywheel. If you never want it to come off I have been told to dust it with talcum powder before assembly. I never tried this, as I wanted them to come off if needed. That's how we did it and I never had a flywheel slip. Hope this helps.

Bill :wai:
 
Status
Not open for further replies.
Top