horsepower

Status
Not open for further replies.

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
Hey I'm new to the site but can tell there is alot of knowledge and experience shared here. I was wondering if anyone could tell about how much hp my 6.5hp clone should have with the current upgrades. Upgrades so far are governor removed 18lbs. springs, a custom header, k&n high flow filter w/billet adapter, arc billet aluminum flywheel, offset keyway 8 degrees advanced, autolite AR3910X plug, 88, &91.5 jet. Haven't tried the jets yet for a plug reading. Also I recently bought a Max Torque torque converter I believe 3-8hp gokartsupply really don't comment much on them only the comets. My question is what if my motor exceeds the hp rating for the converter or the rpm level. Can you modify the converter or will the with stand more than rated? I now alot of rating are low balled. Thanks for any help
 

Jcotz

...wasn't there
Messages
374
Reaction score
1
Location
NY
At higher rpm's (because of the removed gov) you will probably exceed the hp rating on it. This is because the formula for hp is (torque*rpm's)÷5252.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
I would say 9-11hp depending on dyno and clone.
A billet rod, 14cc head and cam change would make your motor 12hp IMO.
 

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
Is there any mods I can do to the torque converter to handle the added power? Any idea what the rpms will be I read 5200prpm without the governor and the aluminum flywheel will up the revs and acceleration. Rod, head and cam are in the future r chez 08, but I gotta make sure my converter can put the power to back wheels. lol hopefully I wont have to buy a new converter again.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
The point of that bump was???

With the torque converter, you are pushing it, with the 18lb springs you could be at over 6k if you have the gearing right. However, most of the power is made at higher rpm. If you really want to modify your engine any more then I would reccomend a comet 40 series.
 

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
could use buy the comet 40 series driven pulley and it work with my new max torque drive pulley or do I have to but the whole 40 series for it to be compatable? Wish we could upgrade these coverters buy swapping parts here and there. Thanks
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Gearing sounds good. Nope, you cannot swap parts between converters. For one, the belts are different sized. Since you have the maxtorque, I suggest you try it. I have no experience with them. But if it is similar to the comet models (3-8hp) you will probably be burning up belts quickly.
 

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
Here's the current situation on the 6.5 clone I mounted the motor today. I ran it but with no load on it, it doesnt want to crank easily before choke on 1 pull slide it half way to warm up and you good. Today I had to give it gas to get it to crank and with the choke closed. It made a little popping noise when I had the choke open trying it. I closed the choke and pressed the gas and it cranked after a few pulls, sound great revs really quick but when revd wot and let off the header backfires not bad but a little pop as it idles down. checked the plug a little white. I'm thinking to lean, gonna pull the 88 jet out and install the 91.5 jet. Do you guy think the bigger jet will help, or do I need a bigget pilot jet. Idle jet is stock only main jet and gx140 emulsion tube. Also is the backfiring normal. Any suggestions or help is appreciated.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
I would try the 91.5 jet, however I expect only a 90 is needed, especially with the 140 e tube.
If it works fine and the plug is good, great!
I would drill the idle jet a little too.
 

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
I put the 91.5 in it seems bout the same hard to start will not start with choke open I wanted the 90 jet but AGK was out of stock on the 90 and sent me the 88 I got the 91.5 from doverpower they didnt carry a 90. You know being impatient and wanting your parts now sometime winds up costing you. What size bit do you recommend drilling the idle jet with. I havent order a valve cover breather yet smoking from the vent when i let off of it.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Before drilling, try unscrewing the brass idle mixture screw a turn or so
And raising the idle with the black screw by the butterfly.
Have a look at this thread- has some rejetting tips.
 

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
well guys I'm writing a bad update to my build. I got the go kart back together Saturday and drove it. It has great take off I can do donuts in the drive way and slide the rearend hard it is a 2 seater with rollbars 18" back tires and with 2 people on it. I took it down the road for a top speed check it ran 34mph I drove it about 20 minutes and the stock rod exploded. I heard the engine die and metal clanking in the motor. I ordered the arc billet rod 0.020 longer than stock and the honda flat top piston. I was planning to order the rod later but it didn't last long at all with the high rpms. Just my advice don't be impatient like me don't drive it til you get the proper upgrade. Also like this site myself thought some of you guys would too, sure some of you already seen it. It's helpful with guessing your horsepower rating with beginning upgrades.http://personalpages.tds.net/~nascarfans/TripleDouble.htm
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
So, let me see if I understand- You had a high dollar flywheel and piston, no governor, 18lb springs, and the stock connecting rod, and the rod let go... Right?
 

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
I had arc billet flywheel, custom header 91.5 main jet gx160 emulsion tube k&n air filter 18lbs. springs no governor ar3910 spark splug offset timing key 8degrees advance stock piston and rod. But yea you right I let go but only topped out the 1 run on the road beside my truck to check top speed the other time in the field in the back doing donuts and a little hill climbing but rpms not held high for long, its only 1.5 acre long and you turn around.
 

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
only seen scratches around the oil drain hole, and a little scratch on the journal of the crank no cracks or holes in the block I drained the oil and didn't see any on the block anywhere. Luckly I just let off the throttle pullede to the side of the road and started to turn around when I gave it gas to turn around on the road it died luckly at low rpms at that moment. few seconds sooner or later it would have been spinning alot faster and I may be ordering a new engine.
 
Status
Not open for further replies.
Top